NEC V850E/IA1 mPD703116 Скачать руководство пользователя страница 381

Страница: 381 / 832

CHAPTER 9 TIMER/COUNTER FUNCTION (REAL-TIME PULSE UNIT)

381

User’s Manual U14492EJ3V0UD

(2) Capture/compare registers 30 and 31 (CC30 and CC31)

These capture/compare registers 30 and 31 are 16-bit registers.

They can be used as capture registers or compare registers according to the CMS1 and CMS0 bit

specifications of timer control register 31 (TMC31).

These registers can be read/written in 16-bit units (however, write operations can only be performed in

compare mode).

Caution

Continuous reading of CC3n is prohibited. If CC3n is continuously read, the second read

value may differ from the actual value. If CC3n must be read twice, be sure to read another

register between the first and the second read operation.

Correct usage example

Incorrect usage example

CC30 read

CC31 read

CC30 read

CC31 read

CC31

CC30

FFFFF682H

FFFFF684H

0000H

Address

Initial value

Address

Initial value

(a) Setting these registers to capture registers (CMS1 and CMS0 of TMC31 = 0)

When these registers are set to capture registers, the valid edges of the corresponding external interrupt

signals INTP30 and INTP31 are detected as capture triggers. The timer TM3 is synchronized with the

capture trigger, and the value of TM3 is latched in the CC30 and CC31 registers (capture operation).

The valid edge of the INTP30 pin is specified (rising, falling, or both edges) according to the IES301 and

IES300 bits of the SESC register, and the valid edge of the INTP31 pin is specified according to the

IES311 and IES310 bits of the SESC register.

The capture operation is performed asynchronously relative to the count clock. The latched value is held

in the capture register until the next capture operation is performed.

When the TM3CAE bit of timer control register 30 (TMC30) is 0, 0000H is read.

If these registers are specified as capture registers, an interrupt is generated by detecting the valid edge

of signals INTP30 and INTP31.

Caution

If the capture operation and the TM3 register count prohibit setting (TM3CE bit of

TMC30 register = 0) timings conflict, the captured data becomes undefined, and no

INTCC3n interrupt is generated (n = 0, 1).

Содержание V850E/IA1 mPD703116

































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание V850E/IA1 mPD703116

Отзывы:

Похожие инструкции для V850E/IA1 mPD703116

Бренды по названию

Популярные бренды

NEC V850E/IA1 mPD703116, Руководство пользователя

Результаты поиска

Содержание V850E/IA1 mPD703116

Отзывы:

Похожие инструкции для V850E/IA1 mPD703116

Бренды по названию

Популярные бренды