NEC V850E/IA1 mPD703116 Скачать руководство пользователя страница 306

Страница: 306 / 832

CHAPTER 9 TIMER/COUNTER FUNCTION (REAL-TIME PULSE UNIT)

306

User’s Manual U14492EJ3V0UD

(5) Capture/compare registers 101, 111 (CC101, CC111)

CC1n1 is a 16-bit register. It can be used as a capture register or as a compare register through specification

with capture/compare control register n (CCRn). CC1n1 can be read/written in 16-bit units.

Cautions 1. When used as a capture register (CMS1 bit of CCRn register = 0), write access from the

CPU is prohibited.

2. When used as a compare register (CMS1 bit of CCRn register = 1) and the TM1CEn bit of

the TMC1n register is “1”, overwriting the CC1n1 register values is prohibited.

3. When the TM1CEn bit of the TMC1n register is “0”, the capture trigger is disabled.

4. When the operation mode is changed from capture register to compare register, newly

set a compare value.

5. Continuous reading of CC1n1 is prohibited. If CC1n1 is continuously read, the second

read value may differ from the actual value. If CC1n1 must be read twice, be sure to read

another register between the first and the second read operation.

Correct usage example

Incorrect usage example

CC101 read

CC111 read

CC101 read

CC111 read

Remark

n = 0, 1

CC101

Address

FFFFF5E8H

Initial value

0000H

CC111

Address

FFFFF608H

Initial value

0000H

(a) When set as a capture register

When CC1n1 is set as a capture register, the valid edge of either corresponding external interrupt signal

INTP1n0 or INTP1n1 is selected with the selector, and the valid edge of the selected external interrupt

signal is detected as the capture trigger. TM1n latches the count value in synchronization with the

capture trigger (capture operation). The latched value is held in the capture register until the next capture

operation.

The valid edge of external interrupts (rising edge, falling edge, both edges) is selected with signal edge

selection register 1n (SESA1n).

When the CC1n1 register is specified as a capture register, interrupts are generated upon detection of

the valid edge of either the INTP1n0 or INTP1n1 signal.

(b) When set as a compare register

When CC1n1 is set as a compare register, it always compares its own value with the value of TM1n. If

the value of CC1n1 matches the value of the TM1n, CC1n1 generates an interrupt signal (INTCC1n1).

Содержание V850E/IA1 mPD703116

































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание V850E/IA1 mPD703116

Отзывы:

Похожие инструкции для V850E/IA1 mPD703116

Бренды по названию

Популярные бренды

NEC V850E/IA1 mPD703116, Руководство пользователя

Результаты поиска

Содержание V850E/IA1 mPD703116

Отзывы:

Похожие инструкции для V850E/IA1 mPD703116

Бренды по названию

Популярные бренды