NEC V850E/IA1 mPD703116 Скачать руководство пользователя страница 302

Страница: 302 / 832

CHAPTER 9 TIMER/COUNTER FUNCTION (REAL-TIME PULSE UNIT)

302

User’s Manual U14492EJ3V0UD

(1) Timers 10, 11 (TM10, TM11)

TM1n is a 2-phase encoder input up/down counter and general-purpose timer.

TM1n can be read/written in 16-bit units.

Cautions 1. Write to TM1n is enabled only when the TM1CEn bit of the TMC1n register is “0” (count

operation disabled).

2. It is prohibited to set the CMD bit (general-purpose timer mode) and the MSEL bit (UDC

mode B) of the TUMn register to “0” and “1”, respectively.

3. Continuous reading of TM1n is prohibited. If TM1n is continuously read, the second

read value may differ from the actual value. If TM1n must be read twice, be sure to read

another register between the first and the second read operation.

Correct usage example

Incorrect usage example

TM10 read

TM11 read

TM10 read

TM11 read

TM10

Address

FFFFF5E0H

Initial value

0000H

TM11

Address

FFFFF600H

Initial value

0000H

TM1n start and stop is controlled by the TM1CEn bit of timer control register 1n (TMC1n).

The TM1n operation consists of the following two modes.

(a) General-purpose timer mode

In the general-purpose timer mode, TM1n operates as a 16-bit interval timer, free-running timer, or for

PWM output.

Counting is performed based on the clock selected by software.

Division by the prescaler can be selected for the count clock from among f

CLK

/2, f

CLK

/4, f

CLK

/8, f

CLK

/16,

CLK

/32, f

CLK

/64, or f

CLK

/128 with bits PRM12 to PRM10 of prescaler mode register 1n (PRM1n). (f

CLK

base clock, refer to

9.2.4 (1) Timer 1/timer 2 clock selection register (PRM02)

Содержание V850E/IA1 mPD703116

































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание V850E/IA1 mPD703116

Отзывы:

Похожие инструкции для V850E/IA1 mPD703116

Бренды по названию

Популярные бренды

NEC V850E/IA1 mPD703116, Руководство пользователя

Результаты поиска

Содержание V850E/IA1 mPD703116

Отзывы:

Похожие инструкции для V850E/IA1 mPD703116

Бренды по названию

Популярные бренды