NEC V850E/IA1 mPD703116 Скачать руководство пользователя | Manualshive

Страница: 571 / 832

background image

CHAPTER 11 FCAN CONTROLLER

571

User’s Manual U14492EJ3V0UD

(2/3)

(a) Read

Bit Position

Bit Name

Function

7

MERR

This is the status flag that indicates an MAC error.

0: Error has not occurred after the MERR bit has been cleared.

1: Error occurred at least once after the MERR bit was cleared.

Caution An MAC error occurs when access to an invalid RAM address is attempted.

3

EFSD

Indicates shutdown request.

0: Shutdown disabled

1: Shutdown enabled

Caution Be sure to set the EFSD bit (to 1) before clearing the GOM bit (to 0) (needs

to be accessed twice). The EFSD bit will be cleared (to 0) automatically

when the CGST register is accessed again.

2

TSM

Indicates the operation status of the time stamp counter

Note

.

0: Time stamp counter is stopped

1: Time stamp counter is operating

Note

See

11.10 (17) CAN time stamp count register (CGTSC)

0

GOM

Indicates the status of the global operation mode.

0: Access to CAN module register

Note

is prohibited

1: Access to CAN module register

Note

is enabled

Note

Register starting with “C1”

Cautions 1. The GOM bit controls the memory access method by the MAC.

• When GOM bit = 0

• Access to the CAN module register is prohibited (if accessed, a

MAC error interrupt occurs).

• Read/write access to the temporary buffer is enabled.

• Access to the message buffer area is enabled.

• When GOM bit = 1

• Access to the CAN module register is enabled.

• Only read access to the temporary buffer is enabled (if a write

access is attempted, a MAC error interrupt occurs).

• Access to the message buffer area is enabled.

2. The GOM bit is cleared to 0 only when all the CAN modules are in the

initial status (when the ISTAT bit of the C1CTRL register = 1). If one of
the CAN modules is not in the initial status, the GOM bit remains set (1)
even if it is cleared to 0.

«
...
569
570
571
572
573
...
»

Содержание V850E/IA1 mPD703116

































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для V850E/IA1 mPD703116

Harmony Controller 2000

Бренд: A10 Страницы: 27

Бренд: ECKELMANN Страницы: 178

Бренд: H3C Страницы: 17

Бренд: H3C Страницы: 32

Бренд: Watts Страницы: 24

Бренд: D+H Страницы: 32

Бренд: Technische Alternative Страницы: 68

Бренд: Bettis Страницы: 18

MURPHYMATIC ASM160

Бренд: Murphy Страницы: 4

Бренд: Swagelok Страницы: 20

Бренд: HANYOUNG NUX Страницы: 4

Бренд: Danfoss Страницы: 6

Бренд: Knoll Страницы: 2

Бренд: VARIZOOM Страницы: 2

HIMatrix F31 02

Бренд: HIMA Страницы: 48

Бренд: LMF Manufacturing Страницы: 51

Бренд: Resol Страницы: 60

Бренд: Lennox Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды