Mindray VS8 Скачать руководство пользователя страница 9

Страница: 9 / 156

VS 9/VS 8 Vital Signs Monitor Service Manual 1

Contents

1 Overview ................................................................................................................... 1-1

1.1 About the Manual..................................................................................................................... 1-1

1.2 Safety Information .................................................................................................................... 1-1

1.2.1 DANGER .......................................................................................................................... 1-1

1.2.2 WARNING ........................................................................................................................ 1-2

1.2.3 CAUTION ......................................................................................................................... 1-2

1.2.4 NOTE ................................................................................................................................. 1-2

1.3 Equipment Symbols ................................................................................................................ 1-3

2 Theory of Operation ................................................................................................. 2-1

2.1 Overview ...................................................................................................................................... 2-1

2.2 Connectors for Peripheral Devices ..................................................................................... 2-2

2.2.1 Connectors for VS9 Peripheral Devices ............................................................... 2-2

2.2.2 Connectors for VS8 Peripheral Devices ............................................................... 2-3

2.3 Block Diagram of Hardware System................................................................................... 2-3

2.3.1 Multi-parameter Module (or Main Board) .......................................................... 2-5

2.4 Power Architecture Diagram ................................................................................................ 2-7

2.5 Data and Information Flow Diagram ................................................................................. 2-8

3 Equipment Installation ............................................................................................ 3-1

3.1 Installation Preparations ........................................................................................................ 3-1

3.1.1 Environmental Requirements ................................................................................. 3-1

3.1.2 Power Supply Requirements ................................................................................... 3-1

3.1.3 Network Requirements ............................................................................................. 3-2

3.1.4 Bracket Strength Requirements ............................................................................. 3-2

3.1.5 Tool Requirements ...................................................................................................... 3-2

3.2 Unpacking ................................................................................................................................... 3-2

3.3 Installation of Accessories ..................................................................................................... 3-3

3.3.1 Installation of Battery ................................................................................................. 3-3

3.3.2 Installation of Parameter Accessories .................................................................. 3-5

3.3.3 Installation of Plug-in Modules (if any) ................................................................ 3-5

3.3.4 Installation of Peripherals (if any) Peripherals Refer to

USB\Bluetooth\network Connected Printers, Scanners, Body Temperature

Modules, Etc. ............................................................................................................................ 3-5

3.4 Installation of the Monitor..................................................................................................... 3-7

3.4.1 Installation of Assemblies and Trolley ............................................................... 3-10

3.5 Post-Installation Checks ...................................................................................................... 3-10

3.5.1 Appearance Check ................................................................................................... 3-10

3.5.2 Power-on Self-test .................................................................................................... 3-11

4 Maintenance and Test .............................................................................................. 4-1

4.1 Introduction ................................................................................................................................ 4-1

Содержание VS8




























































































































































Результаты поиска

Содержание VS8

Отзывы:

Похожие инструкции для VS8

Бренды по названию

Популярные бренды

Mindray VS8, Руководство по обслуживанию

Результаты поиска

Содержание VS8

Отзывы:

Похожие инструкции для VS8

Бренды по названию

Популярные бренды