Mindray VS8 Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 156

background image

6-1

5

Troubleshooting

5.1

Overview

In this chapter, monitor problems are listed along with possible causes and

recommended corrective actions. Refer to the tables to check the monitor and identify

and eliminate these problems.
The recommended solutions given in this chapter address most of the equipment

problems you encounter, but do not include any problems that may arise. Contact us if

you have a problem that is not covered in this section.

5.2

Parts Replacement

Printed circuit boards (PCBs) and other major parts and components in the monitor are
replaceable. Once you isolate a PCB you suspect defective, follow the instructions in

Disassembly and Maintenance

to replace the PCB with a good one. Verify proper

operation and that the monitor passes all performance tests. If the failure is eliminated, it

indicates that the original PCB is damaged. In this case, send the defective PCB to us for
repair. If the fault remains, reinstall the PCB and continue troubleshooting as directed in

this chapter.

To learn about and get the parts you need to replace, refer to

5.3

Check before Powering on the Monitor

After the AC power supply is connected, check whether the AC indicator is turned on. If
not, confirm whether the AC cable is connected to the socket and monitor reliably. If both

the AC external power supply and power cord are connected normally, but the AC

indicator is off, the AC-DC power module or main board of the main unit may be

damaged. Now, you need to insert a battery to see whether the monitor can be powered
on. If it cannot be powered on, the main board may be damaged or the internal board is

abnormal, resulting in power supply protection. If the monitor can be powered on, the

AC-DC power module is damaged.
In addition, check the appearance for damages before powering on. Particularly, when

the touch screen of the display assembly is damaged, stop using the monitor

immediately.

5.4

Software Version Check

In troubleshooting that involves software version compatibility, you need to know the

monitor configuration and software version information. For detailed information about
version compatibility, contact our after-sales service department. To check the software

version, follow this procedure:

«
...
61
62
63
64
65
...
»

Содержание VS8





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для VS8

Бренд: 2B Technologies Страницы: 4

Бренд: VeEX Страницы: 2

Portable Grand DGX-670

Бренд: Yamaha Страницы: 93

Portatone PSR-410

Бренд: Yamaha Страницы: 65

Бренд: H-Star Страницы: 36

Бренд: Kane Страницы: 35

Бренд: Veris Страницы: 3

Бренд: Primes Страницы: 56

Бренд: Michell Instruments Страницы: 28

Бренд: 3nh Страницы: 39

Бренд: TEA Страницы: 10

DUAL-BLEND 4114

Бренд: NCL Страницы: 7

Бренд: Bamo Страницы: 16

Бренд: Velleman Страницы: 18

Бренд: Jäger Direkt Страницы: 6

Бренд: sauermann Страницы: 2

Бренд: Hach Страницы: 176

Бренд: Bushnell Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды