Mindray VS8 Скачать руководство пользователя страница 137

Страница: 137 / 156

VS 9/VS 8 Vital Signs Monitor Service Manual

8-9



Tap

on the touchscreen or press the



arrow key on the

keyboard to switch the upgrade program upward.



Tap

on the touchscreen or press the



arrow key on

the keyboard to switch the upgrade program leftward.



Tap

on the touchscreen or press the



arrow key on the

keyboard to switch the upgrade program rightward.



Tap

on the touchscreen or press the

Enter

key on the

keyboard to confirm the selected upgrade program.

8.2.3.4

Completing Upgrade

When the screen below is displayed, the current upgrade is completed. The upgrade

takes effect after the monitor is restarted.

CAUTION



Disconnect the monitor from the patient and make sure that important
data are saved before upgrade.



Do not shut down or power off the equipment when upgrading the BIOS
program and FPGA program. Otherwise, the equipment may break down.



Program upgrade can be performed only by qualified service personnel.
Indicates unsafe service practice that, if not avoided, could result in slight
injury, product fault, or property loss.

Содержание VS8




























































































































































Результаты поиска

Содержание VS8

Отзывы:

Похожие инструкции для VS8

Бренды по названию

Популярные бренды

Mindray VS8, Руководство по обслуживанию

Результаты поиска

Содержание VS8

Отзывы:

Похожие инструкции для VS8

Бренды по названию

Популярные бренды