Mindray VS8 Скачать руководство пользователя страница 11

Страница: 11 / 156

VS 9/VS 8 Vital Signs Monitor Service Manual

5.6 Troubleshooting Guide ........................................................................................................... 5-2

5.6.1 Power-On/Off Failures ............................................................................................... 5-2

5.6.2 Display Failures ............................................................................................................. 5-2

5.6.3 Alarm Lamp Failures ................................................................................................... 5-3

5.6.4 Button and Knob Failures ......................................................................................... 5-3

5.6.5 Sound Failure ................................................................................................................ 5-4

5.6.6 Battery Failures ............................................................................................................. 5-4

5.6.7 Recorder Failures ......................................................................................................... 5-5

5.6.8 Output Connector Failure......................................................................................... 5-5

5.6.9 Data Storage Failure ................................................................................................... 5-5

5.6.10 Wired Network Failures ........................................................................................... 5-5

5.6.11 Wi-Fi Failures ............................................................................................................... 5-6

5.6.12 Module Failure ........................................................................................................... 5-7

5.6.13 Software Upgrade Failure ...................................................................................... 5-7

5.6.14 Technical Alarm Messages ..................................................................................... 5-8

6 Disassembly and Maintenance ................................................................................ 6-1

6.1 Disassembly Preparations ..................................................................................................... 6-1

6.2 Whole Unit Disassembly Flowchart ................................................................................... 6-2

6.2.1 VS9 Disassembly Flowchart ..................................................................................... 6-2

6.2.2 VS8 Disassembly Flowchart ..................................................................................... 6-3

6.3 (A) Disassembly of VS9 Main Unit ....................................................................................... 6-4

6.3.1 (A-1) Body Temperature Module ............................................................................ 6-4

6.3.2 (A-2) Recorder Assembly/Door ............................................................................... 6-6

6.3.3 (B) Removing Rear Cover .......................................................................................... 6-7

6.3.4 (B-1) Rear Cover Assembly .................................................................................... 6-11

6.3.5 (C) Removing Components on the Main Support and Front Cover
Assembly ................................................................................................................................ 6-13

6.3.6 (D) Disassembling the Assembly into the Main Frame Assembly and Front

Cover Assembly ................................................................................................................... 6-17

6.3.7 Removing the Main Support Assembly D ....................................................... 6-18

6.3.8 (G) Removing the Sheet Metal Main Support and Plastic Main Support

Assemblies ............................................................................................................................. 6-19

6.3.9 (F) Plastic Main Support Assembly ..................................................................... 6-21

6.3.10 (E) Front Cover Assembly .................................................................................... 6-21

6.4 (A) Disassembling the VS8 Main Unit ............................................................................. 6-24

6.4.1 (A-1) Body Temperature Module ......................................................................... 6-25

6.4.2 (A-2) Recorder Assembly/Door ............................................................................ 6-27

6.4.3 (B) Removing Rear Cover ....................................................................................... 6-29

6.4.4 (D) Detaching the Main Frame and Front Cover Assembly ....................... 6-36

6.4.5 (F) Detaching the Plastic Support ....................................................................... 6-37

6.4.6 (G) Sheet Metal Main Support Assembly ......................................................... 6-39

6.4.7 (E) Front Cover Assembly ....................................................................................... 6-41

7 Parts ........................................................................................................................... 7-1

7.1 Introduction ................................................................................................................................ 7-1

Содержание VS8




























































































































































Результаты поиска

Содержание VS8

Отзывы:

Похожие инструкции для VS8

Бренды по названию

Популярные бренды

Mindray VS8, Руководство по обслуживанию

Результаты поиска

Содержание VS8

Отзывы:

Похожие инструкции для VS8

Бренды по названию

Популярные бренды