Mindray VS8 Скачать руководство пользователя страница 68

Страница: 68 / 156

5-6 VS 9/VS 8 Vital Signs Monitor Service Manual

Fault Symptom

Possible Cause

Troubleshooting

The IP address is
incorrect.

Check whether an IP address conflict exists in
the network. If yes, reset the IP address.

Connector board
damaged

Replace the connector board

The main board is
faulty

Replace the main board

The network

connection is
disconnected

frequently.

The network cable

fails to be
connected

properly.

Check LAN cable connection. LAN cable should
not be longer than 50m.

The monitor is
connected to a

network but

cannot view
other patients

in the View

Others mode

The network cable

fails to be

connected
properly.

Check LAN cable connection. LAN cable should

not be longer than 50m.

There are too many
monitors to be

viewed.

One monitor could only be observed by four
monitors simultaneously, and the observing

requests not within the range would not be

handled.

The IP address is

incorrect.

Check whether an IP address conflict exists in

the network. If yes, reset the IP address.

5.6.11

Wi-Fi Failures

Fault Symptom

Possible Cause

Troubleshooting

Frequent dropouts

or network

disconnects

Wi-Fi signals in the region are

instable.

Check the Wi-Fi connection of

the hospital.

The Wi-Fi- antenna falls off or is

not securely connected to the

module.

Disassemble the monitor and

fix the Wi-Fi antenna properly.

Antenna damaged

Replace the antenna

The Wi-Fi module is faulty

Replace the Wi-Fi module

The monitor fails to
connect Wi-Fi

The IP address is incorrect.

Check whether an IP address

conflict exists in the network.
If yes, reset the IP address.

Wi-Fi signals in the region are
instable.

Check the Wi-Fi connection of
the hospital

The Wi-Fi antenna falls off or is
disconnected from the Wi-Fi

module

Secure the Wi-Fi antenna

Antenna damaged

Replace the antenna

The Wi-Fi module is faulty

Replace the Wi-Fi module

The main board is faulty

Replace the main board

Содержание VS8




























































































































































Результаты поиска

Содержание VS8

Отзывы:

Похожие инструкции для VS8

Бренды по названию

Популярные бренды

Mindray VS8, Руководство по обслуживанию

Результаты поиска

Содержание VS8

Отзывы:

Похожие инструкции для VS8

Бренды по названию

Популярные бренды