Mindray VS8 Скачать руководство пользователя страница 136

Страница: 136 / 156

8-8 VS 9/VS 8 Vital Signs Monitor Service Manual

8.2.3.2

Entering the Upgrade Mode



Method 1: Power off the monitor, and connect the monitor to a USB keyboard.
Press the power key to power on the monitor. During the power-on, keep

pressing F4+F5 at the same time or press * to enter the upgrade mode to

perform upgrade.



Method 2: Power off the monitor. Press the power key to power on the monitor.

During the power-on, keep sliding two or more fingers on the touchscreen to

enable the monitor to enter the upgrade mode.

8.2.3.3

Selecting the File for Upgrade

Only one upgrade package file is available at present. It is selected by default. If multiple

upgrade packages exist, they are displayed in the left and right columns, and a maximum
of 16 upgrade packages can be displayed. This upper limit cannot be exceeded. You can

use the up, down, left and right keys to switch and select the required upgrade package.



Tap

on the touchscreen or press the



arrow key on the

keyboard to switch the upgrade program downward.

Содержание VS8




























































































































































Результаты поиска

Содержание VS8

Отзывы:

Похожие инструкции для VS8

Бренды по названию

Популярные бренды

Mindray VS8, Руководство по обслуживанию

Результаты поиска

Содержание VS8

Отзывы:

Похожие инструкции для VS8

Бренды по названию

Популярные бренды