Mindray VS8 Скачать руководство пользователя страница 34

Страница: 34 / 156

3-10 VS 9/VS 8 Vital Signs Monitor Service Manual

After completing the setup wizard, you can restart the monitor.
You can tap

Advanced Settings

to set the network and workflow.

You can insert an USB flash drive into the monitor and tap

Export Configuration

to save

the current power-on setup wizard.

3.4.1

Installation of Assemblies and Trolley

Optional assemblies and trolley are available for the monitor. For specific installation
methods, refer to the

New VS Trolley Installation Instructions (PN: H-046-020003-00)

Sanitizer Bracket Installation Instructions (PN: H-046-020269-00)

Assembly

Installation Instructions for Basket with Handle (PN: H -046-020270-00)

Writing Panel

Assembly Instructions (PN: H-046-020271-00)

Assembly Instructions for Basket

without handle (PN: H-046-020272-00)

3.5

Post-Installation Checks

The monitor has been tested before it is shipped from the factory. In order to ensure that
the monitor was not damaged during transportation, complete the following checks

after installation.

3.5.1

Appearance Check

After installation, check the appearance of the monitor and accessories.

Procedure

Check items

Check whether the appearance of the monitor has obvious damage, such

as damage to the enclosure.

Содержание VS8




























































































































































Результаты поиска

Содержание VS8

Отзывы:

Похожие инструкции для VS8

Бренды по названию

Популярные бренды

Mindray VS8, Руководство по обслуживанию

Результаты поиска

Содержание VS8

Отзывы:

Похожие инструкции для VS8

Бренды по названию

Популярные бренды