Mindray VS8 Скачать руководство пользователя страница 65

Страница: 65 / 156

VS 9/VS 8 Vital Signs Monitor Service Manual

5-3

5.6.3

Alarm Lamp Failures

Fault Symptom

Possible Cause

Troubleshooting

Alarm lamp off or

cannot be turned

off, or alarm lamp

displays
abnormally

Cable failure

1. Verify the cable connecting the alarm lamp

board to the main board is properly connected.

2. Verify the cables and connectors are not
damaged.

Alarm lamp
board failure

Replace the alarm lamp board.

The main board
is faulty

Replace the main board

5.6.4

Button and Knob Failures

Fault Symptom

Possible Cause

Troubleshooting

Buttons do not

work

Cable failure

Verify the cable connecting the button board

to the main board is properly connected.

Button board

failure

Replace the button board

Knob does not
work

Cable failure

1. Verify the connection cable between the

knob and the button board.
2. Verify the cable connecting the button

board to the main board is properly

connected.

Knob damaged

Replace the rotary encoder.

Button board
failure

Replace the button board

Cable failure

1. Verify the signal cable and backlight

cable connecting the display to the

main board are correctly connected.

The touchscreen
does not respond.

Touchscreen disabled

Check if there is a symbol

shown

above the key on the main menu. If
yes, press Main Menu for more than 3s

to enable the touchscreen.

Cable failure

1. Verify the cable connecting the
touchscreen to the touchscreen

control board is properly connected.

2. Verify the cable connecting the
touchscreen control board to the main

board is properly connected.

Touchscreen control

board defective

Replace the touchscreen control board.

Touch screen defective

Replace the touchscreen

The main board is faulty

Replace the main board

Содержание VS8




























































































































































Результаты поиска

Содержание VS8

Отзывы:

Похожие инструкции для VS8

Бренды по названию

Популярные бренды

Mindray VS8, Руководство по обслуживанию

Результаты поиска

Содержание VS8

Отзывы:

Похожие инструкции для VS8

Бренды по названию

Популярные бренды