Fuji Electric FRENIC-Ace series Скачать руководство пользователя страница 327

Страница: 327 / 788

5.3 Description of Function Codes

5-157

NCT

Chap 5

H04, H05

Auto-reset (Times and reset interval)

H04 and H05 specify the auto-reset function that makes the inverter automatically attempt to reset the tripped state

and restart without issuing an alarm output (for any alarm) even if any protective function subject to reset is

activated and the inverter enters the forced-to-stop state (tripped state). If the protective function is activated in

excess of the times specified by H04, the inverter will issue an alarm output (for any alarm) and not attempt to

auto-reset the tripped state.
Listed below are the protective functions subject to auto-reset.

Protective function

LED monitor displays:

Protective function

LED monitor displays:

Overcurrent protection

0c1

0c2

0c3

Motor overheat

0h4

Overvoltage protection

0u1

0u2

0u3

Braking resistor overheat

dbh

Heat sink overheat

0h1

Motor overload

0l1

0l2

Inverter internal overheat

0h3

Inverter overload

0lu

■

Number of reset times (H04)

H04 specifies the number of reset times for the inverter to automatically attempt to escape the tripped state. When

H04 = 0, the auto-reset function will not be activated.

•

Data setting range: 0 (Disable), 1 to 20 (times)

If the “auto-reset” function has been specified, the inverter may automatically restart and run the motor stopped

due to a trip fault, depending on the cause of the tripping. Design the machinery so that human body and

peripheral equipment safety is ensured even when the auto-resetting succeeds.

Otherwise an accident could occur.

■

Reset interval (H05)

•

Data setting range: 0.5 to 20.0 (s)

H05 specifies the reset interval time between the time when the inverter enters the tripped state and the time when

it issues the reset command to attempt to auto-reset the state. Refer to “Operation timing scheme” below.

•

In the figure below, normal operation restarts in the 4-th retry.

Protective function

Tripped state

Tripped state reset

command

Inverter output

frequency

Auto-resetting

[TRY]

1st

2nd

3rd

4th

Time

Содержание FRENIC-Ace series





















































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание FRENIC-Ace series

Отзывы:

Бренды по названию

Популярные бренды

Fuji Electric FRENIC-Ace series, Руководство пользователя

Результаты поиска

Содержание FRENIC-Ace series

Отзывы:

Бренды по названию

Популярные бренды