Fuji Electric FRENIC-Ace series, Руководство пользователя

Страница: 175 / 788

5.2 Function Codes Table
5-5
FU
NCT
IO
N
C
O
DE
S
Chap 5
Code Name Data setting range
C
han
ge
w
hen
ru
nni
ng
D
at
a
co
py
in
g
Factory
Default
Drive control
R
el
at
ed
p
ag
e
V
/f
PG
V/
f
w
/ P
G
Tor
qu
e c
on
tro
l
PM
F14 Restart mode after momentary
power failure (Mode selection)
0: Trip immediately
1: Trip after a recovery from power failure
2: Trip after momentary deceleration is stopped
3: Continue to run (for heavy inertia load or general load)
4: Restart from frequency at power failure (for general
load)
5: Restart from starting frequency
Y Y EU: 0
ACJK:1
Y Y Y N Y 5-66
F15 Frequency limiter (Upper limit) 0.0 to 500.0Hz Y Y 70.0 Y Y Y N Y 5-73
F16 (Lower limit) 0.0 to 500.0Hz Y Y 0.0 Y Y Y N Y
F18 Bias (for frequency setting 1) -100.00 to 100.00% Y* Y 0.00 Y Y Y N Y 5-73
F20 DC braking 1
(Braking starting frequency)
0.0 to 60.0Hz Y Y 0.0 Y Y Y N Y 5-74
F21 (Braking level) 0 to 100% (HHD mode), 0 to 80% (HD/HND mode) 0 to 60%
(ND mode )
Y Y 0 Y Y Y N Y
F22 (Braking time) 0.00 (Disable): 0.01 to 30.00 s Y Y 0.00 Y Y Y N Y
F23 Starting frequency 1 0.0 to 60.0Hz Y Y 0.5 Y Y Y N Y 5-77
F24 (Holding time) 0.00 to 10.00 s Y Y 0.00 Y Y Y N Y
F25 Stop frequency 0.0 to 60.0 Hz Y Y 0.2 Y Y Y N Y
F26 Motor sound
(Carrier frequency)
ND mode
- 0.75 to 10 kHz (FRN0002 to 0059E2

-4

)
- 0.75 to 6 kHz (FRN0072E2

-4

or above)
HD/HND mode
- 0.75 to16 kHz (FRN0001 to 0088E2

-2

)
- 0.75 to16 kHz (FRN0002 to 0059E2

-4

)
- 0.75 to16 kHz (FRN0001 to 0012E2

-7

)
- 0.75 to10 kHz (FRN0072 to 0168E2

-4

)
- 0.75 to10 kHz (FRN0115E2

-2

)
- 0.75 to 6 kHz (FRN0203E2

-4

or above)
HHD mode
- 0.75 to16 kHz (FRN0001 to 0115E2

-2

)
- 0.75 to16 kHz (FRN0002 to 0168E2

-4

)
- 0.75 to16 kHz (FRN0001 to 0012E2

-7

)
- 0.75 to10 kHz (FRN0203E2

-4

or above)
Y Y 2 Y Y Y Y Y 5-80
F27 (Tone) 0: Level 0 (Disable)
1 to 3 : Level 1 to 3
Y Y 0 Y Y N N N
F29 Terminal FM (Mode selection) 0: Voltage output (0 to +10 VDC)
1: Current output (4 to 20 mA DC)
2: Current output (0 to 20 mA DC)
3: Pulse output
Y Y 0 Y Y Y Y Y 5-81
F30 (Output gain) 0 to 300% Y* Y 100 Y Y Y Y Y
F31 (Function selection) 0: Output frequency 1 (before slip compensation)
1: Output frequency 2 (after slip compensation)
2: Output current
3: Output voltage
4: Output torque
5: Load factor
6: Input power
7: PID feedback value
8: Actual speed/estimated speed *5
9: DC link bus voltage
10: Universal AO
13: Motor output
14: Calibration (+)
15: PID command (SV)
16: PID output (MV)
17: Position error in master-follower operation *5
18: Inverter heat sink temperature
21: PG feedback value *5
111 to 120 Customizable logic output signal 1 to 10
Y Y 0 Y Y Y N Y
F32 Terminal FM 2 *1
(Mode selection)
0: Voltage output (0 to +10 VDC)
1: Current output (4 to 20 mA DC)
2: Current output (0 to 20 mA DC)
Y Y 0 Y Y Y Y Y
F33 Terminal FM (Pulse rate) 25 to 32000 p/s
(number of pulse at monitor value 100%)
Y* Y 1440 Y Y Y Y Y
F34 Terminal FM 2 *1
(Output gain)
0 to 300%
Y* Y 100 Y Y Y Y Y
F35 (Function selection) Same as F31
Y Y 2 Y Y Y N Y
Factory default

A (For Asia), C (for China), E (for Europe), U (For USA), J (for Japan), K (for Korea)
indicates quick setup target function code.
*1: F34 and F35 only exist for GB model and C model (for China).
*5: Available at ROM version 0300 or later.