Fuji Electric FRENIC-Ace series, Руководство пользователя

Страница: 188 / 788

5.2 Function Codes Table
5-18
Code Name Data setting range
C
han
ge
w
hen
ru
nni
ng
D
at
a
co
py
in
g
Factory
Default
Drive control
R
el
at
ed
p
ag
e
V
/f
PG
V/
f
w
/ P
G
Tor
qu
e c
on
tro
l
PM
H47 Initial capacitance of DC link
bus capacitor
For adjustment at replacement
(0000 to FFFF in hexadecimal)
Y N – Y Y Y Y Y 5-173
H48 Cumulative run time of
capacitors on printed circuit
boards
For adjustment at replacement
Change in cumulative motor run time (Reset is enabled)
(in units of ten hours)
Y N – Y Y Y Y Y 5-169
5-173
H49 Starting mode
(Auto search delay time 1)
0.0 to 10.0 s Y Y 0.0 Y Y Y N Y 5-174
H50 Non-linear V/f 1 (Frequency) 0.0 (Cancel), 0.1 to 500.0 Hz N Y 0.0 Y Y N N N 5-174
H51 (Voltage) 0 to 240 V:AVR operation ( 200 V class)
0 to 500V:AVR operation ( 400V class)
N Y2 0 Y Y N N N
H52 Non-linear V/f 2 (Frequency) 0.0 (Cancel), 0.1 to 500.0 Hz N Y 0.0 Y Y N N N
H53 (Voltage) 0 to 240V:AVR operation ( 200V class)
0 to 500V:AVR operation ( 400V class)
N Y2 0 Y Y N N N
H54 Acceleration time (Jogging) 0.00 to 6000 s Y Y 6.00
or
20.0
*10
Y Y Y N Y 5-174
H55 Deceleration time (Jogging) 0.00 to 6000 s Y Y Y Y Y N Y
H56 Deceleration time for forced
stop
0.00 to 6000 s Y Y Y Y Y N Y
H57 1st S-curve acceleration range
(At starting)
0 to 100% Y Y 10 Y Y Y N Y
H58 2nd S-curve acceleration
range (At arrival)
0 to 100% Y Y 10 Y Y Y N Y
H59 1st S-curve deceleration
range (At starting)
0 to 100% Y Y 10 Y Y Y N Y
H60 2nd S-curve deceleration
range (At arrival)
0 to 100% Y Y 10 Y Y Y N Y
H61 UP/DOWN control
(Initial frequency setting)
0: Initial value is 0.00 Hz
1: Last UP/DOWN command value on releasing the run
command.
N Y 1 Y Y Y N Y 5-174
H63 Low limiter (Mode selection) 0: Limit by F16 (Frequency limiter: Low) and continue to
run
1: If the output frequency lowers below the one limited by
F16 (Frequency limiter: Low), decelerate to stop the
motor.
Y Y 0 Y Y Y N Y 5-174
H64 (Lower limiting frequency) 0.0: Depends on F16 (Frequency limiter, Low)
0.1 to 60.0 Hz
Y Y 1.6 Y Y N N Y 5-174
H65 Non-linear V/f 3 (Frequency) 0.0 (Cancel), 0.1 to 500.0 Hz N Y 0.0 Y Y N N N 5-174
H66 (Voltage) 0 to 240V: AVR operation ( 200V class)
0 to 500V: AVR operation ( 400V class)
N Y2 0 Y Y N N N
H68 Slip compensation 1
(Operating conditions
selection)
0: Enable during acceleration/deceleration, enable at
base frequency or higher
1: Disable during acceleration/deceleration, enable at
base frequency or higher
2: Enable during acceleration/deceleration, disable at
base frequency or higher
3: Disable during acceleration/deceleration, disable at
base frequency or higher
N Y 0 Y Y N N N 5-174
H69 Anti-regenerative control
(Mode selection)
0: Disable
2: Torque limit control with force-to-stop
(Cancel limit control after three times of deceleration
time has passed)
3: DC link bus voltage control with force-to-stop
(Cancel voltage control after three times of deceleration
time has passed)
4: Torque limit control without force-to-stop
5: DC link bus voltage control without force-to-stop
Y Y 0 Y Y Y N Y 5-175
H70 Overload prevention control 0.00: Follow the deceleration time selected
0.01 to 100.00 Hz/s, 999 (Cancel)
Y Y 999 Y Y Y N Y 5-176
H71 Deceleration characteristics 0: Disable 1: Enable Y Y 0 Y Y Y N N 5-176
H72 Main power shutdown
detection
(Mode selection)
0: Disable 1: Enable
(Available FRN0088E2

-2

/FRN0059E2

-4

or above)
Y Y 1 Y Y Y Y Y 5-176
H74 Torque limiter *5
(Control target)
0: Torque limit
1: Torque current limit
N Y 1 N N Y Y Y 5-177
H76 Torque limiter (Braking)
(Frequency rising limiter for
braking)
0.0 to 500.0Hz Y Y 5.0 Y Y N N N 5-177
H77 Service life of DC link bus
capacitor
0 to 8760 (in units of ten hours) Y N 6132
(ND spec)
Y Y Y Y Y 5-177
*5: Available at ROM version 0300 or later.
*10: 6.00s for inverters of nominal applied motor 22kW or below; 20.0s for those of 30kW or above.