Fuji Electric FRENIC-Ace series, Руководство пользователя

Страница: 192 / 788

5.2 Function Codes Table
5-22
Code Name Data setting range
C
han
ge
w
hen
ru
nni
ng
D
at
a
co
py
in
g
Factory
Default
Drive control
R
el
at
ed
p
ag
e
V
/f
PG
V/
f
w
/ P
G
Tor
qu
e c
on
tro
l
PM
A23 Motor 2
(Slip compensation gain for
driving)
0.0 to 200.0% Y* Y 100.0 Y Y Y N N
A24 (Slip compensation response
time)
0.01 to 10.00 s Y Y1
Y2
0.50 Y Y N N N
A25 (Slip compensation gain for
braking)
0.0 to 200.0% Y* Y 100.0 Y Y Y N N
A26 (Rated slip frequency) 0.00 to 15.00Hz N Y1
Y2
*6 Y Y Y N N
A27 (Iron loss factor 1) 0.00 to 20.00% Y Y1
Y2
*6 Y Y Y Y N
A30 (Magnetic saturation factor 1)
*5
0.0 to 300.0 % Y Y1
Y2
*6 N N Y Y N
A31 (Magnetic saturation factor 2)
*5
0.0 to 300.0 % Y Y1
Y2
*6 N N Y Y N
A32 (Magnetic saturation factor 3)
*5
0.0 to 300.0 % Y Y1
Y2
*6 N N Y Y N
A33 (Magnetic saturation factor 4)
*5
0.0 to 300.0 % Y Y1
Y2
*6 N N Y Y N
A34 (Magnetic saturation factor 5)
*5
0.0 to 300.0 % Y Y1
Y2
*6 N N Y Y N
A39 Motor 2 selection 0: Motor characteristics 0 (Fuji standard IM, 8-series)
1: Motor characteristics 1 (HP rating IMs)
4: Other IMs
N Y1
Y2
U:1
ACEJK:0
Y Y Y Y N
A40 Slip compensation 2
(Operating conditions
selection)
0: Enable during acceleration/deceleration, enable at
base frequency or higher
1: Disable during acceleration/deceleration, enable at
base frequency or higher
2: Enable during acceleration/deceleration, disable at
base frequency or higher
3: Disable during acceleration/deceleration, disable at
base frequency or higher
N Y 0 Y Y N N N
A41 Output current fluctuation
damping gain for motor 2
0.00 to 1.00 Y Y 0.20 Y Y N N N
A43 Speed control 2 *5
(Speed command filter)
0.000 to 5.000 s Y Y 0.020 N Y Y N Y 5-228
A44 (Speed detection filter) 0.000 to 0.100 s Y* Y 0.005 N Y Y N Y
A45 P (Gain) 0.1 to 200.0 times Y* Y 10.0 N Y Y N Y
A46 I (Integral time) 0.001 to 9.999 s; 999 (Cancel integral term) Y Y 0.100 N Y Y N Y
A47 FF (Gain) 0.00 to 99.99 s Y Y 0.00 N N Y N Y
A49 (Notch filter resonance
frequency)
1 to 200 Hz Y Y 200 N N Y N N
A50 (Notch filter attenuation level) 0 to 20 dB Y Y 0 N N Y N N
A51 Cumulative motor run time 2 0 to 9999
Change in cumulative motor run time (Reset is enabled)
(in units of 10 hours)
N N – Y Y Y Y N –
A52 Startup counter for motor 2 For adjustment at replacement
(0000 to FFFF in hexadecimal)
Y N – Y Y Y Y N
A53 Motor 2
(%X correction factor 1)
0 to 300% Y Y1
Y2
100 Y Y Y Y N
A55 (Torque current under vector
control) *5
0.00 to 2000 A N Y1
Y2
*6 N N Y Y N
A56 (Induced voltage factor under
vector control) *5
50 to 100 % N Y1
Y2
*6 N N Y Y N
A98 Motor 2
(Function selection)
0 to 255
(Data is displayed in decimal, Meaning of each bit 0:
Disable; 1 Enable)
bit0: Current limiter (F43, F44)
bit1: Rotational direction control (H08)
bit2: Non-linear V/f (H50 to H53, H65, H66)
bit3: PID control (J01 to J62, H91)
bit4: Brake signal
bit5: Braking timer at the Startup (H195)
Bit6 to 7: Reserved *9
N Y 0 Y Y Y Y Y 5-195
Factory default

A (For Asia), C (for China), E (for Europe), U (For USA), J (for Japan), K (for Korea)
*5: Available at ROM version 0300 or later.
*6: Factory defaults are depended on motor capacity. Refer to “5.2.4 Motor constant”.
*9: Factory use. Do not change these function codes.