Fuji Electric FRENIC-Ace series, Руководство пользователя

Страница: 204 / 788

5.2 Function Codes Table
5-34
Code Name Data setting range
C
han
ge
w
hen
ru
nni
ng
D
at
a
co
py
in
g
Factory
Default
Drive control
R
el
at
ed
p
ag
e
V
/f
PG
V/
f
w
/ P
G
Tor
qu
e c
on
tro
l
PM
y21 Built-in CAN communication
(Node ID)
1 to 127 N Y 1 Y Y Y Y Y 5-280
y24 (Baud rate) 0: 125kbps
1: 20kbit/s
2: 50kbit/s
3: 125kbit/s
4: 250kbit/s
5: 500kbit/s
6: 800kbit/s
7: 1Mbit/s
N Y 0 Y Y Y Y Y
y25 Map the inverter function
code1 to RPDO No. 3
0000 to FFFF (in hexadecimal) N Y 0000 Y Y Y Y Y
y26 Map the inverter function
code2 to RPDO No. 3 Data mapped I/O (Write)
Y Y Y Y Y
y27 Map the inverter function
code3 to RPDO No. 3
Y Y Y Y Y
y28 Map the inverter function
code4 to RPDO No. 3
Y Y Y Y Y
y29 Map the inverter function
code1 to TPDO No. 3
Y Y Y Y Y
y30 Map the inverter function
code2 to TPDO No. 3
Y Y Y Y Y
y31 Map the inverter function
code3 to TPDO No. 3
Y Y Y Y Y
y32 Map the inverter function
code4 to TPDO No. 3
Y Y Y Y Y
y33 (Operation selection) 0: Disable, 1: Enable Y Y 0 Y Y Y Y Y
y34 (Communications error
processing)
This function code is valid in case of y36=-4 or -5.
1: After the time specified by [y35], coast to a stop and trip
with [ert].
2: If the inverter receives any data within the time specified
by [y35], ignore the communications error. After the
timeout, coast to a stop and trip with [ert].
10: Immediately decelerate to a stop. Issue [ert] after
stopping.
11: After the time specified by [y35], decelerate to a stop.
Issue [ert] after stopping.
12: If the inverter receives any data within the time specified
by [y35], ignore the communications error. After the
timeout, decelerate to a stop and trip with [ert].
Otherwise: Immediately coast to a stop and trip with [ert].
Y Y 0 Y Y Y Y Y
y35 (Communication time-out
detection timer)
0.0 to 60.0 Y Y 0.0 Y Y Y Y Y
y36 (Operation selection in abort
status) *5
-5 to 3 Y Y 1 Y Y Y Y Y
y95 Data clear processing for
communications error
0: Do not clear the data of function codes Sxx when a
communications error occurs. (compatible with the
conventional inverters)
1: Clear the data of function codes S01/S05/S19 when a
communications error occurs.
2: Clear the run command assigned bit of function code
S06 when a communications error occurs.
3: Clear both data of S01/S05/S19 and run command
assigned bit of S06 when a communications error
occurs.
* Related alarms:
er8
,
erp
,
er4
,
er5
,
ert
Y Y 0 Y Y Y Y Y 5-280
y97 Communication data storage
selection
0: Store into nonvolatile memory (Rewritable times are
limited)
1: Write into temporary memory (Rewritable times are
unlimited)
2: Save all data from temporary memory to nonvolatile
memory (After all save, return to Data 1)
Y Y 0 Y Y Y Y Y 5-280
y98 Bus link function
(Mode selection)
Frequency command Run command
0: Follow H30 Follow H30
1: Bus link Follow H30
2: Follow H30 Bus link
3: Bus link Bus link
Y Y 0 Y Y Y Y Y 5-280
y99 Loader link function
(Mode selection)
Frequency command Run command
0: Follow H30, y98 Follow H30, y98
1: FRENIC loader Follow H30, y98
2: Follow H30, y98 FRENIC loader
3: FRENIC loader FRENIC loader
Y N 0 Y Y Y Y Y 5-281
*5: Available at ROM version 0300 or later.