Docomo FOMA N901IC, Руководство пользователя, Страница: 83 / 596

81
Making/Receiving Video-phone
Calls
Continued on next page
Receiving a Video-phone Call
Use this procedure to accept an incoming video-phone call. If you cannot answer a video-phone call immediately,
you can still receive the call without showing the caller the image from your camera by displaying a substitute image
(alternate image).
1
When you receive a video-phone call, press
e
to answer
the call.
■
To answer using the alternate image
Press
r
or
d
.
The alternate image appears on the caller’s display.
After sending the alternate image, you can still change to the camera image by
pressing
e
.
■
When using an earphone/microphone with switch (optional)
Press the switch on the earphone/microphone with switch.
Display Reason
Check the number and retry You dialed the number incorrectly.
Busy The called party is on another call or using i-mode or packet communication.
Out of service area or power off The called party is out of signal range or his/her phone is turned off.
Driving mode The called party’s phone is in Driving mode.
Select on for Call ID Notification Displayed when you connected without disclosing your caller ID (when dialing into V-LIVE or Visualnet).
Your call is being forwarded The call is being forwarded.
Connection failed Set Notify caller ID to “ON” and then try again.
・ This message may also be displayed in other situations.
Note
● If you make a video-phone call to an emergency number (110, 119 or 118) from the FOMA terminal, the call is automatically changed to a voice call.
● If you make a video-phone call to a phone that does not support video-phone calls, or if the called party’s phone supports video-phone calls but is
out of signal range or switched off, no connection can be established. If you called a phone that does not support video-phone calls and “Voice call
auto switch” is set to “ON”, the call is cut off by the called party before the video-phone connection is established and is then automatically redialed
as a voice call. However, this operation is not carried out if you dial the wrong number or if you call an ISDN synchronous 64K or PIAFS access point
or an ISDN video-phone that does not conform to the 3G-324M standard (as at December 2004). Note that call charge may apply in some cases.
● The “32K” dialing speed allows you to use video-phones or other devices (PHS mobiles, etc.) that cannot communicate at “64K” due to network
conditions. If you make a video-phone call at “64K” and the called party is in a “32K” area or similar situation, the call is automatically redialed at 32K
bps. However, note that “32K” video-phone calls attract the same digital communication charges as “64K” video-phone calls.
● If an attempted “64K” video-phone call fails to connect when “Voice call auto switch” is set to “ON”, it automatically switches to the “32K” dialing
speed. If the video-phone call still fails to connect, it switches to voice-call mode. The table below shows how “Voice call auto switch” and automatic
connection speed switching operate when a video-phone call fails to connect.
●
Once a video-phone is successfully connected, it is not re-dialed as a voice call.
●
You cannot receive i - mode mail or a Message Request/Free during a video-phone call. Received mail is held at the i - mode center and can be
retrieved using “Check new message” once the video-phone is completed.
●
You cannot receive SMS during a video-phone call.
●
If the “Recharge battery” battery low alarm appears on the display during a video-phone call, the other party sees the “Camera Off” message and
the call is disconnected roughly 20 seconds later. Even if you start charging the battery before the call is terminated, the “Camera Off” message
remains on the display.
●
Digital call charges still apply when the alternate image is displayed during a video-phone call.
“Voice call auto
switch” set to ON The dialing speed automatically changes to “32K”. If
the video-phone call still fails to connect, it switches
to voice-call mode. Switches to voice-call mode.
“Voice call auto
switch” set to OFF The connection speed automatically changes to
“32K”. If the video-phone call still fails to connect, the
video-phone call ends. Ends the video-phone call.
Dialing speed set to “64K” Dialing speed set to “32K”
Video-phone call reception display
Ａｎｓｗｅｒ
［Ｖ−ｐｈｏｎｅ ｃａｌｌ］
ＦＵＮＣ