Docomo FOMA N901IC, Руководство пользователя, Страница: 523 / 596

521
Data Comm
unication
<Maximum bitrate DL> ※ : None (initial value) or
384
*: <cid> is a number for managing the access point
name (APN) registered in the FOMA terminal for a
packet communication. For the FOMA terminal,
you can register from number 1 to 10. <Maximum
bitrate UL> and <Maximum bitrate DL> set the
minimum communication speed (kbps) of uplink
and downlink between the FOMA terminal and
base station. When it is set to “None” (initial
value), all speeds will be permitted, but when set
to 64 or 384, a connection at a speed of other
values will not be permitted, at which time a
packet communication may not be connected.
・ Operation performed when the parameter is omitted
+CGEQMIN=: Set the default value to all <cid>.
+CGEQMIN=<cid>: Set the specified <cid> to the
default value.
・
Command execution example
Only the following 4 patterns can be set. (1) is set as
an initial value to each cid.
(1) Command for permitting all speeds of both
uplink and downlink (when cid is 2)
AT+CGEQMIN=2
OK
(2) Command for permitting only the speed of
uplink 64kbps and downlink 384kbps (when
cid is 3)
AT+CGEQMIN=3,,64,384
OK
(3) Command for permitting uplink 64kbps and all
speeds of downlink (when cid is 4).
AT+CGEQMIN=4,,64
OK
(4) Command for permitting all speeds of uplink
and only 384kbps of downlink (when cid is 5)
AT+CGEQMIN=5,,,384
OK
■ Command name: +CGEQREQ=[parameter]
・ Outline
Set the QoS (quality of service) to be requested to
network when originating a PPP packet
communication.
For setting, only the pattern shown in the command
execution example can be set, which is also set as
an initial value.
Although this command is a setting command, it will
not be recorded in non-volatile memory written by
[&W], nor reset by [&F] or [Z].
・ Format
+CGEQREQ=[<cid>]
・
Explanation of the parameters
<cid>
* : 1 to 10
*: <cid> is a number for managing the access point
name (APN) registered in the FOMA terminal for a
packet communication. For the FOMA terminal,
you can register from number 1 to 10.
・
Operation performed when the parameter is omitted
+CGEQREQ=: Set the default value to all <cid>.
+CGEQREQ=<cid>: Set the specified <cid> to the
default value.
・ Command execution example
Only the following pattern can be set. This is set to
each cid as an initial value.
Command for requesting a connection at a speed of
uplink 64kbps and downlink 384kbps (when cid is 3).
AT+CGEQREQ=3
OK
Saving modem port command setting value
The values set by AT commands are initialized every time
the power of FOMA terminal is turned on or off, except the
access point name (APN) set by AT+CGDCONT command
(P. 498), QoS setting by AT+CGEQMIN/AT+CGEQREQ
command, permit or reject setting by AT
＊ DGAPL/AT ＊
DGARL/AT
＊
DGANSM command and the setting for
specifying sending/not sending caller ID of packet
communication set by AT
＊
DGPIR command. However,
you can save the values set by commands with [&W] if you
enter
AT&W
after the setting. In this case, other set values with [&W] will
also be saved. These values can be retrieved by entering
ATZ
even after the power is turned on or off.