Club Car CARRYALL 272 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 312

background image

2006-2010 Turf/Carryall 272/472 and XRT 1200/1200 SE Maintenance and Service Manual

Page i

FOREWORD

Club Car vehicles are designed and built to provide the ultimate in performance efficiency; however, proper
maintenance and repair are essential for achieving maximum service life and continued safe and reliable
operation.
This manual provides detailed information for the maintenance and repair of the Turf/Carryall 272/472 and
XRT 1200/1200 SE vehicles, and should be thoroughly reviewed prior to servicing the vehicles. The proce-
dures provided must be properly implemented, and the DANGER, WARNING, and CAUTION statements
must be heeded.
This manual was written for the trained technician who already possesses knowledge and skills in electrical
and mechanical repair. If the technician does not have such knowledge and skills, attempted service or
repairs to the vehicle may render the vehicle unsafe. For this reason, Club Car advises that all repairs and/or
service be performed by an authorized Club Car distributor/dealer representative or by a Club Car factory-
trained technician.
It is the policy of Club Car, LLC to assist its distributors and dealers in continually updating their service knowl-
edge and facilities so they can provide prompt and efficient service for vehicle owners. Regional technical rep-
resentatives, vehicle service seminars, periodic service bulletins, maintenance and service manuals, and
other service publications also represent Club Car’s continuing commitment to customer support.
Club Car offers a full line of training and continuing education classes for technicians who want to learn more
about our products. For more information, contact your local dealer or Club Car’s Technical Services depart-
ment for a list of upcoming classes.
This manual covers all aspects of typical vehicle service; unique situations, however, sometimes occur when
servicing a vehicle. If it appears that a service question is not answered in this manual, you may write to us at:
Club Car, LLC, P.O. Box 204658; Augusta, GA 30917, Attention: Technical Services.

Copyright © 2006, 2007, 2010 Club Car, LLC

Club Car

and

Carryall

are registered trademarks of Club Car, LLC.
This manual effective July 25, 2005.

«
1
2
3
4
5
...
»

Содержание CARRYALL 272

























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CARRYALL 272

Бренд: E-Z-GO Страницы: 95

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды