manualshive.com logo in svg

Club Car CARRYALL 272, Руководство по техническому обслуживанию и ремонту

Поделиться
Скачать
Club Car CARRYALL 272 Скачать руководство пользователя страница 23

GENERAL INFORMATION

Storage

2006-2010 Turf/Carryall 272/472 and XRT 1200/1200 SE Maintenance and Service Manual

Page 3-3

3

11. Plug the fuel tank vent nipple so that it is air tight using a slip-on vinyl cap.

12. Wash tops and terminals of battery with a solution of baking soda and water (1 cup (237 mL) baking soda

per 1 gallon (3.8 L) of water). Rinse solution off battery. Do not allow this solution to enter the battery. 

13. Remove spark plug and pour 1/2 ounce of SAE 10 weight oil into the engine through the spark plug hole.

Rotate engine crankshaft by hand several times, then install spark plug and tighten to 20 ft-lb (27 N·m).

14. Adjust tires to rated capacities. 

See General Information, Section 8, Page 8-1.

15. Lubricate front suspension and do all other semiannual periodic lubrication. 

See Periodic Lubrication

Schedule, Section 10, Page 10-3.

16. Thoroughly clean body, seats, cargo bed, engine compartment and underside of vehicle.

17. Do not engage the park brake. Chock the wheels to prevent the vehicle from rolling.

TO RETURN VEHICLE TO SERVICE

1. Make sure the key switch is OFF and the Forward/Reverse handle is in the NEUTRAL position. Remove

the key. Chock the wheels.

2. Remove plug from vent tube and connect to tank vent 

(Figure 3-2, Page 3-3

 

or

 

Figure 3-3, Page 3-3)

.

3. Connect battery and spark plug wire(s). 

See Connecting The Battery on page 1-3.

4. Completely open fuel shut-off valve 

(Figure 3-4, Page 3-4 and Figure 3-5, Page 3-4)

. A partially closed

fuel valve combined with the use of the choke, can result in a fouled spark plug and engine failure.

5. Make sure the Forward/Reverse handle is in the NEUTRAL position.

6. Crank the engine until it starts. Turn the engine off. 

See following NOTE.

NOTE: 

Due to the oil added to the engine in preparation for storage, engine may smoke excessively for a
short time when it is run for the first time after storage.

7. Adjust tires to recommended tire pressure. 

See General Information, Section 8, Page 8-1.

 

  

Figure 3-2   Turf-CA 272/XRT 1200 Fuel Tank

Figure 3-3   Carryall 472/XRT 1200 SE Fuel Tank

1. Vent Tube* 2. To Carburetor 3. Vent 4. Fuel Shut-off Valve 5. 
Fuel Tank
*Vehicle without carbon canister shown.

1. Vent Tube 2. Fuel Tank 3. Vent 4. Fuel Shut-off Valve 5. Fuel 
Pump (under rear seat) 6. Fuel Filter (under rear seat)

1

4

5

3

2

1

3

4

5

6

2

A

A

Содержание CARRYALL 272

























































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды