Club Car CARRYALL 272, Руководство по техническому обслуживанию и ремонту

Страница: 236 / 312

FUEL SYSTEM Choke and Air Intake System
Page 14-12 2006-2010 Turf/Carryall 272/472 and XRT 1200/1200 SE Maintenance and Service Manual
14
CHOKE AND AIR INTAKE SYSTEM
See General Warning, Section 1, Page 1-1.
CHOKE CABLE REMOVAL
1. Turn the key switch to OFF and remove the key. Place the Forward/Reverse handle in the NEUTRAL
position. Chock the wheels.
2. Remove the screw (17) securing cable to air box and detach cable end from choke lever (6)
(Figure 14-10, Page 14-15 or Figure 14-11, Page 14-16) .
3. Remove three screws (19), nuts (21) and washers (20) from body and remove choke cable assembly
from body.
4. Carryall 472/XRT 1200 SE:
4.1. Cut wire tie (23) around cable and air duct (Figure 14-11, Page 14-16) .
CHOKE CABLE INSTALLATION
1. Insert choke cable through hole in body until choke lever assembly seats against body.
2. Install three screws (19), washers (20), and locknuts (21)
(Figure 14-10, Page 14-15 or Figure 14-11,
Page 14-16) . Tighten to 18 in-lb (2.0 N·m).
3. Check the hex nut on the cable at the back of the choke lever assembly and tighten it until the lockwasher
beside it collapses completely.
4. Attach choke cable to choke lever (6) on air box top (4) and install screw (17) to secure cable to air box.
Tighten screw to 18 in-lb (2.0 N·m).
5. Carryall 472/XRT 1200 SE:
5.1. Attach a new wire tie (23) around the cable and air duct (Figure 14-11, Page 14-16) .
AIR BOX REMOVAL
1. Turn the key switch OFF and remove the key. Place the Forward/Reverse handle in the NEUTRAL posi-
tion. Chock the wheels.
2. Remove choke cable bracket screw (17) and cable (18) from air box top (4) (Figure 14-10, Page 14-15
or Figure 14-11, Page 14-16) .
3. Turf 272/Carryall 272/XRT 1200:
3.1. Remove air intake box (12) from the vehicle by removing hose clamp (15), intake hose (16), three
screws (23) and washers (22) (Figure 14-10, Page 14-15) .
4. Carryall 472/XRT 1200 SE:
4.1. Remove air intake box (12) from the vehicle by removing hose clamp (15), intake hose (16), three
screws (25) and washers (24) (Figure 14-11, Page 14-16) .
AIR BOX INSTALLATION
NOTE: The intake duct must be in place before the air box can be installed.
1. Check to be sure the intake seal (13) is tightly seated (Figure 14-10, Page 14-15 or Figure 14-11,
Page 14-16) . The seal fits tightly onto the bottom side of the air box. If seal is not in place, moisture will
enter the air intake system.
2. Turf 272/Carryall 272/XRT 1200:
2.1. Place air box assembly into vehicle and install three flat washers (22) and screws (23) from under-
side of air box mounting plate into air box (12) (Figure 14-10, Page 14-15) . Tighten to 33 in-lb (3.7
N·m).