Club Car CARRYALL 272 Скачать руководство пользователя страница 207

Страница: 207 / 312

ELECTRICAL COMPONENTS: FE400, KEY-START ENGINE

Oil Level Sensor

2006-2010 Turf/Carryall 272/472 and XRT 1200/1200 SE Maintenance and Service Manual

Page 12-37

OIL LEVEL SENSOR

See General Warning, Section 1, Page 1-1.

Testing the Oil Level Sensor

See Test Procedure 21, Section 11, Page 11-32.

Oil Level Sensor Removal

See Oil Level Sensor Installation, Section 13, Page 13-5.

Oil Level Sensor Installation

See Oil Level Sensor Installation, Section 13, Page 13-5.

HEADLIGHTS

See General Warning, Section 1, Page 1-1.

Testing the Headlight Socket

See Test Procedure 30, Section 11, Page 11-40.

Headlight Bulb Removal

1. Turn the key switch OFF and remove the key. Place the Forward/Reverse handle in the NEUTRAL posi-

tion. Chock the wheels.

2. Disconnect battery and spark plug wire(s).

See Disconnecting The Battery on page 1-3.

3. From the front of vehicle, reach under cowl and turn the wire harness/halogen bulb assembly (4 and 6)

clockwise one-quarter turn

(Figure 12-43, Page 12-37)

4. Remove the wire harness/halogen bulb assembly (4 and 6) from the headlight lens (7).

5. Lift the retaining tabs on the connector (4) and remove halogen bulb assembly (6).

Headlight Bulb Installation

NOTE:

When handling halogen bulbs, do not touch glass portion of bulb. Oil from finger tips can cause
premature failure of bulb.

Figure 12-43 Headlight Assembly

Содержание CARRYALL 272

























































































































































































































































































































Результаты поиска

Содержание CARRYALL 272

Отзывы:

Бренды по названию

Популярные бренды

Club Car CARRYALL 272, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание CARRYALL 272

Отзывы:

Бренды по названию

Популярные бренды