3D Systems DMP Flex 350 Скачать руководство пользователя

Страница: 94 / 120

3D Systems, Inc.

p/n: 15-D100, rev. D

5. Switch on the power meter device. The battery of the device

must be sufficiently loaded.

6. Set the readout device to the correct wavelength (

1064 Nm

7. Use duct tape to fix the cables to the frame of the process

chamber.

8. Close the printer door and handtighten the door bolt in the

upper right corner.

Caution: Do not crush the cable between the

printer door and the frame of the process

chamber.

9. Use laser safety tape (

p/n: 80-4392

Black Aluminum Foil

Tape 2” x 81’) to seal of the gap between printer door and

frame.

10. Turn the service key ON.
11. Open the DMP toolbar and log in as an

Engineer

12. Open DMP Control. In the task bar, click

Machine

Laser

Laser Power Calibration

to open the Laser power

calibration window.

13. When the device is connected for the first time and no

drivers are installed, an error message will appear.

14. Browse to the Ophir website indicated in the error message

(url linked here) to download the StarLab software.

Caution: Disconnect the power meter from the

USB port when installing the StarLab software to

avoid driver issues.

Note: Remove the StarLab icon from the computer

desktop as this application will never be used.

Содержание DMP Flex 350

























































































































Результаты поиска

Содержание DMP Flex 350

Отзывы:

Похожие инструкции для DMP Flex 350

Бренды по названию

Популярные бренды

3D Systems DMP Flex 350, Руководство пользователя

Результаты поиска

Содержание DMP Flex 350

Отзывы:

Похожие инструкции для DMP Flex 350

Бренды по названию

Популярные бренды