3D Systems DMP Flex 350 Скачать руководство пользователя

Страница: 44 / 120

3D Systems, Inc.

p/n: 15-D100, rev. D

4.4.8 Building Close to the Platform Borders

DMP Control shows the preferred calibrated build area with the light colored contour. Attempting to print outside of this area

will have a significant influence on the accuracy. Optically, you will not damage the machine or the part as long as you stay away

from the 4 corners.

Caution: Do not scan on the build module. The scanner zero point is not always in the center of the build

platform.

To verify that your part is not outside of the platform, you can ‘test’ the location by manually pointing the scanner to the test

location.

1. Switch on the red laser diode/pointer to see the location of the spot.
2. Select

Machine

Laser

> check ‘

Show laser diode

’

3. From DMP Control, select

Machine

Scanner

Direct scanner control

4. Move the scanner to the requested ‘test’ location and verify it is inside the build plate.
5. If the spot is not inside the build plate, shift your part in DMP Control to match the real position.

Содержание DMP Flex 350

























































































































Результаты поиска

Содержание DMP Flex 350

Отзывы:

Похожие инструкции для DMP Flex 350

Бренды по названию

Популярные бренды

3D Systems DMP Flex 350, Руководство пользователя

Результаты поиска

Содержание DMP Flex 350

Отзывы:

Похожие инструкции для DMP Flex 350

Бренды по названию

Популярные бренды