3D Systems DMP Flex 350 Скачать руководство пользователя

Страница: 32 / 120

3D Systems, Inc.

p/n: 15-D100, rev. D

Laser window

: the laser is focused onto the build platform through the laser window.

Control box

: allows user to operate the system while reaching inside the process

chamber through the glove ports.

•  Emergency off button (a)
•  Mode Select button (b)
•  Hold-to-run button (c)
•  Action lever (d)

RPM (Removable Printer Module)

: the RPM contains the metal powder and the build platform. It can be pulled

outwards to have better access to the build platform for a powder switch, cleaning or maintenance. It can be removed

and replaced by another RPM that contains a different metal powder. For more detailed information on the RPM, see

next page.

Locking pins

: the locking pins lock the build module into place and maintain it in the correct position. These must be

unlocked to pull the module in its outward position or to remove it.

Содержание DMP Flex 350

























































































































Результаты поиска

Содержание DMP Flex 350

Отзывы:

Похожие инструкции для DMP Flex 350

Бренды по названию

Популярные бренды

3D Systems DMP Flex 350, Руководство пользователя

Результаты поиска

Содержание DMP Flex 350

Отзывы:

Похожие инструкции для DMP Flex 350

Бренды по названию

Популярные бренды