3D Systems DMP Flex 350 Скачать руководство пользователя

Страница: 102 / 120

3D Systems, Inc.

p/n: 15-D100, rev. D

Inlet

valve

Outlet

valve

5. Unscrew the philips screw on the oxygen sensor and

disconnect the sensor from the outlet valve.

6. Remove the KF-clamps on inlet and outlet valves of the process filter (see images below).

7. Roll out the process filter cart to a safe and secure location.
8. Disconnect and remove the KF50 clamp between the

outlet valve and the process filter (see image to the right).

Remove the filter outlet valve assembly and the centering

ring with stand-off. The centering ring may stick slightly

to the filter housing. If needed, pry it loose with a plastic

tool (such as a scraper).

9. As you lift the centering ring away from the

filter,simultaneously check to make certain the spring-

loaded valve has closed.

WARNING: THE FILTER OUTLET PORT MUST BE

CAPPED IMMEDIATELY AFTER THE FILTER OUTLET

VALVE ASSEMBLY IS REMOVED.

Содержание DMP Flex 350

























































































































Результаты поиска

Содержание DMP Flex 350

Отзывы:

Похожие инструкции для DMP Flex 350

Бренды по названию

Популярные бренды

3D Systems DMP Flex 350, Руководство пользователя

Результаты поиска

Содержание DMP Flex 350

Отзывы:

Похожие инструкции для DMP Flex 350

Бренды по названию

Популярные бренды