3D Systems DMP Flex 350 Скачать руководство пользователя

Страница: 67 / 120

3D Systems, Inc.

p/n: 15-D100, rev. D

3. Loosen 6 Allen head bolts.
4. Place new silicone strip in the recoater housing. Tighten all

the bolts from one side to the other and ensure the silicone

strip is fixed.

5. Place the recoater housing in the lower part of the coater

cutting tool. Place the upper part of the coater cutting tool

on top.

6. Use a sharp utility knife to cut the recoater in one smooth

motion.

WARNING: BE CAREFUL WHEN CUTTING THE

RECOATER. THIS PRESENTS A CUTTING DANGER.

7. Leave the recoater housing in the upper part of the coater

cutting tool and cut the ends of the silicone strip where

they stick out of the recoater housing. Cut the corners at

a 45° edge. Check if the silicone strip is smooth with no

irregularities. If the recoater is not smooth, use a new

silicon strip and cut it again, repeating Steps 2-5.

8. Re-attach recoater housing to recoater bridge.

Содержание DMP Flex 350

























































































































Результаты поиска

Содержание DMP Flex 350

Отзывы:

Похожие инструкции для DMP Flex 350

Бренды по названию

Популярные бренды

3D Systems DMP Flex 350, Руководство пользователя

Результаты поиска

Содержание DMP Flex 350

Отзывы:

Похожие инструкции для DMP Flex 350

Бренды по названию

Популярные бренды