3D Systems DMP Flex 350 Скачать руководство пользователя | Manualshive

Страница: 84 / 120

background image

3D Systems, Inc.

79

p/n: 15-D100, rev. D

5.8 Emergency Off

5.8.1 Location

The DMP Flex 350 systems is equipped with 2 emergency off buttons:

•  1 x on the control panel of the printer
•  1 x on the control box inside the process chamber
•  1 x on the enable switch (located at the rear control panel)

5.8.2 What Happens?

Pressing one of these buttons will activate a

Category 0 emergency stop

which will immediately remove all power to the

machine actuators, i.e. an uncontrolled stop.
All printer valves will be closed. The argon will remain sealed in the process chamber and pressure levels will stay at a constant

level. A mechanical pressure release valve will open if the pressure level inside the process chamber continues to rise after an

emergency stop.
Main argon and compressed air valves are closed and pressure is released from the flexible tube.
DMP Deposition closes automatically.

«
...
82
83
84
85
86
...
»

Содержание DMP Flex 350

























































































































Отзывы:

Нет отзывов

Похожие инструкции для DMP Flex 350

Бренд: Xerox Страницы: 168

Бренд: Xerox Страницы: 36

Бренд: Xerox Страницы: 64

Бренд: Xerox Страницы: 54

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 115

Бренд: Labau Страницы: 19

Бренд: Ultimaker Страницы: 30

Бренд: Canon Страницы: 21

Бренд: TierTime Страницы: 28

VersaLink C400V

Бренд: Xerox Страницы: 196

Line Printer VIII

Бренд: Radio Shack Страницы: 54

Бренд: Xerox Страницы: 34

Бренд: Oce Страницы: 32

Бренд: Star Micronics Страницы: 194

Бренд: Pringo Страницы: 2

Бренд: Aficio Страницы: 92

Бренд: TEC Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды