URAL Motorcycles URAL-4320-60 Operation Manual Download

Page: 204 / 267

203

Mobilube GX 140,
Shell pirax GX
140

7,5

M-(1500-3000)

Check oil level and

add, if need be

Every third M-15 000

Change oil. Add oil

up to the edge of the fill-
er neck on the reduction
gear case cover.

STATOIL
TRANSWAY
PS DX III

6,5

Daily Maintenance (DM)

Check oil level in the

steering booster pump
tank and add, if need be

M-(1500-3000)

Every third M-15 000

When repairing steering hy-

draulic booster

Change oil (together

with  filter  changing)  and
check  oil  level  in  the
steering  booster  pump
tank

2,7

5,4

M-(1500-3000)

M-15 000

Check oil level in the

unit and add, if need be.
Fill up to the control fill-
er edge

Every third M-15 000,

but at least once in three

years

Change lubricant

Summary of Contents for URAL-4320-60












































































































































































































































































Search results

Summary of Contents for URAL-4320-60

Reviews:

Related manuals for URAL-4320-60

Brands by name

Popular brands

URAL Motorcycles URAL-4320-60, Operation Manual

Search results

Summary of Contents for URAL-4320-60

Reviews:

Related manuals for URAL-4320-60

Brands by name

Popular brands