URAL Motorcycles URAL-4320-60 Operation Manual Download

Page: 187 / 267

186

Description

Technical requirements

Recommended equipment,
accessories and tools

Wheel ar-

rangement

Check and retighten the

fastening of engine starting
preheater

high-voltage

source, if required

Fastening should be

tight

Screwdriver

Check condition of rubber

jackets  on  rear  lights,    side
turn repeaters, storage battery
switch,  braking  signal,  fuel
level  sensor,  auxiliary  brake
switch

Ditto

Visual inspection

Special equipment

Check the power take-off

case fastening to the gearbox
case and oil pump fastening to
the power take-off case (if
available)

Fastening should be

tight

Wrench 14x17

Lubrication

Engine lubrication should

be carried out as per Engine
Operation Manual

Check oil level in the

steering knuckle housings of
front driving axle and bring to
the norm, if required

Change oil:
- in the transfer gearbox

case      (see  the  subsections
«Transmission»  and  «Chart
of  lubricants  and  operating
fluids»)

Pour oil in up to the

inspection/fill  opening  on
the rear  wall  of  the  case.
Oil  leakage  through  the
plugs is not admissible

Wrench 27x30, vessel

for used oil, oil dispenser
133

, wiping material

Change lubricant in driv-

ing axles final drives

Pour oil in up to the

inspection/fill  opening  on
the rear  wall  of  the  case.
Oil  leakage  through  the
plugs is not admissible

Wrench 27x30, vessel

for used oil, oil dispenser
133

Lubricate in accordance

with the Chart of Lubricants
and Working Fluids:

Summary of Contents for URAL-4320-60












































































































































































































































































Search results

Summary of Contents for URAL-4320-60

Reviews:

Related manuals for URAL-4320-60

Brands by name

Popular brands

URAL Motorcycles URAL-4320-60, Operation Manual

Search results

Summary of Contents for URAL-4320-60

Reviews:

Related manuals for URAL-4320-60

Brands by name

Popular brands