URAL Motorcycles URAL-4320-60 Operation Manual Download Page 181

Page: 181 / 267

180

8.3 List of maintenance operations

Description

Technical requirements

Recommended equipment,
accessories and tools

Wheel ar-

rangement

Daily maintenance (DM)

Maintenance before leaving

Inspect the truck and

check  absence  of  fuel,  oil,
brake  fluid  and  coolant,  as
well  as  air  leaks;  eliminate
troubles if any

Inspect the engine; clean it

from dust and dirt, if re-
quired.

Check oil level in booster

pump tank, add required

Oil level should be be-

tween upper and lower
marks on oil level gauge

Oil level gauge, wiping

material

Fill the windshield washer

pump tank in

At sub-zero tempera-

tures drain water from the
tank

Vessel

Check good repair and

service3ability of lighting de-
vices, light and sound alarms,
instrumentation and wind-
shield wipers

Faults can not be toler-

ated

Check operation of the

generator against current in-
dicator

The current indicator

should show the charging
current

Current indicator

Check for good working

order of:

- clutch;

Clutch should provide

complete  and  smooth  en-
gagement  (without  slip-
ping),  completer  disen-
gagement  (without  drag-
ging)

-steering gear;

Steering rod and boost-

er  pin  nuts  should  be
cottered,  play  in  the  joints
can  not  be  tolerated,  loose
propeller  shafts  forks  fas-
teners are impermissible

Visual check

Summary of Contents for URAL-4320-60












































































































































































































































































Search results

Summary of Contents for URAL-4320-60

Reviews:

Brands by name

Popular brands

URAL Motorcycles URAL-4320-60, Operation Manual

Search results

Summary of Contents for URAL-4320-60

Reviews:

Brands by name

Popular brands