Peripheral Installation
Relay Control Options and Door Lock Control
Strata DK I&M 6/00
12-17
Pe
ri
p
h
er
a
l In
st
al
la
ti
on
Configure PIOU, PIOUS or PEPU for Night Transfer
1. In Program 77-1, set LED 05 to Off to configure the Night/Hold Relay for the Night Transfer
function (see
2. In Program 77-1, set LED 06 to provide continuous or pulsating relay activation:
♦
Off – Programs the relay for continuous activation when the
1LJKW7UDQVIHU
button
(only) is set in the Night mode.
♦
On – Programs the relay for pulsating activation when the
1LJKW7UDQVIHUa
button
for tenant 1~4 is set to the Night mode and a CO line rings.
Note
CO lines must be enabled in Program 78 for the Night Transfer pulsating relay function.
3. Set in Programs 87, 88, and 89 the CO lines that will activate the relay (when the system is in
the Night mode).
4. Assign, in Program 39, the
1LJKW7UDQVIHU
buttons to telephones that should be able to set
the Strata DK system into the Night mode.
5. Assign in Programs 29-1~29-4 a
1LJKW7UDQVIHU
button on all direct station selection
consoles that are to transfer the Strata DK system into the Night mode.
6. If tenant operation is required, set in Program *15 the CO lines for tenant 1 through tenant 4
operation. DK40i and the DK424 RCTUA and RCTUB provides two tenant assignments,
RCTUC/D provides four.
7. If using a PIOU or PEPU, set the P11 jumper plug on the PIOU or PEPU to the MAKE or
BREAK position, as required:
♦
MAKE – Shorts the normally open contacts (pins 9 and 34) when the night relay is
activated.
♦
BREAK – Opens the normally closed contacts (pins 9 and 34) when the night relay is
activated.
...or
If using a PIOUS, solder the jumper W2 on the PIOUS to the MAKE or BREAK position, as
required:
♦
MAKE – Shorts the normally open contacts (NHT and NHR) when the night relay is
activated.
♦
BREAK – Opens the normally closed contacts (NHT and NHR) when night relay is
activated.
8. See
for wiring/interconnecting details. Connect the PIOU, PIOUS, or
PEPU to the MDF as required for the night relay function.
Note
Door phones programmed to ring over external page in the Night mode do not activate the
Night Transfer feature, per Program 77-1.
Configure PIOU, PIOUS, or PEPU for MOH Relay Control
1. In Program 77-1, set LED 05 to On to configure the Night/MOH relay for the MOH relay
function (see
Summary of Contents for Strata AirLink DK40i
