manualshive.com logo in svg

Teledyne T101, Operation Manual, Page: 7 / 375

Share
Download
Teledyne T101 Operation Manual Download Page 7

 

 

iii 

SAFETY MESSAGES 

Important safety messages are provided throughout this manual for the purpose of 
avoiding  personal injury or instrument damage.  Please read these messages 
carefully.  Each safety message is associated with a safety alert symbol. They are 
placed throughout this manual.  The safety symbols are also located inside the 
instrument. It is imperative that you pay close attention to these messages, the 
descriptions  of which are as follows: 

 

WARNING: Electrical Shock Hazard 

 

HAZARD: Strong oxidizer 

 

GENERAL WARNING/CAUTION:  Read  the accompanying 

message  for specific information. 

 

CAUTION:  Hot Surface Warning 

 

Do Not Touch:   Touching  some  parts of the instrument 

without protection or proper tools could result in damage to the 

part(s) and/or the instrument. 

 

Technician Symbol: All operations marked  with this symbol 

are to be performed  by qualified  maintenance  personnel  only. 

 

Electrical Ground: This symbol  inside the instrument marks 

the central safety grounding  point for the instrument. 

 

 

CAUTION 

This  instrument  should only be used for the purpose  and in the 

manner described in this manual.  If you use this  instrument  in a 

manner other than that for which  it was intended, unpredictable 

behavior could ensue with  possible hazardous consequences. 

NEVER  use any gas analyzer to sample combustible gases! 

Note 

For Technical Assistance  regarding the use and maintenance of this instrument or any other 

Teledyne ML product, contact Teledyne ML’s Technical Support Department: 

Telephone: 800-846-6062 

Email:  [email protected] 

or access any of the service options  on our website at 

http://www.teledyne-ml.com/

 

Summary of Contents for T101
























































































































































































































































































































































































Reviews:

No comments