Teledyne T101 Operation Manual Download Page 316

Page: 316 / 375

Teledyne API T/E-Series Models 101, 102, and 108 Software Documentation (PN05492D DCN6485)

A-22

WPMTTEMP

PMT TEMP WARNING

PMT temperature outside of warning

limits specified by PMT_SET variable.

WDARKCAL

DARK CAL WARNING

Dark offset above limit specified by

DARK_LIMIT

variable.

WHVPS

HVPS WARNING

High voltage power supply output

outside of warning limits specified by

HVPS_SET

variable.

WDYNZERO

CANNOT DYN ZERO

Contact closure zero calibration

failed while DYN_ZERO was set to

WDYNSPAN

CANNOT DYN SPAN

Contact closure span calibration

failed while DYN_SPAN was set to

WREARBOARD

REAR BOARD NOT DET

Rear board was not detected during

power up.

WRELAYBOARD

RELAY BOARD WARN

Firmware is unable to communicate

with the relay board.

WFRONTPANEL

FRONT PANEL WARN

Firmware is unable to communicate

with the front panel.

WANALOGCAL

ANALOG CAL WARNING

The A/D or at least one D/A channel

has not been calibrated.

The name is used to request a message via the RS-232 interface, as in “T BOXTEMP”.

Engineering

software.

Current instrument units.

T101,

M101E.

Triple-gas

option.

T108,

M108E.

Concentration alarm option.

T108U, M108EU.

Optional.

07266B DCN6485

Summary of Contents for T101
























































































































































































































































































































































































Search results

Summary of Contents for T101

Reviews:

Teledyne T101, Operation Manual, Page: 316 / 375

Search results

Summary of Contents for T101

Reviews: