manualshive.com logo in svg

Teledyne T101, Operation Manual, Page: 164 / 375

Share
Download
Teledyne T101 Operation Manual Download Page 164

Remote Operation 

Teledyne  ML  – T101 Operation Manual 

160 

  

5.1.4.7.

 

Setting Hessen Protocol Status Flags 

Teledyne  ML’s  implementation of Hessen protocols includes a set of status bits that the 
instrument includes in responses to inform the host computer of  its condition. Each bit 
can be assigned to one operational and warning message flag.  The default settings for 
these bit/flags are: 

Table 5-8. Default Hessen Status Bit Assignments 

 

 

NOTES 

It is possible to assign more than one flag to the same Hessen status bit.  This  allows  the 

grouping  of similar flags, such as all temperature warnings,  under the same status bit.  

Be careful not to assign conflicting  flags to the same bit as each status bit will  be 

triggered if any of the assigned flags is active.  

STATUS FLAG NAME 

DEFAULT BIT 

ASSIGNMENT 

WARNING FLAGS 
SAMPLE FLOW WARNING 

0001 

PMT DET WARNING 

0002 

UV LAMP WARNING 

0002 

HVPS WARNING 

0004 

DARK CAL WARNING 

0008 

RCELL TEMP WARNING 

0010 

IZS TEMP WARNING 

0020 

PMT TEMP WARNING 

0040 

CONV TEMP WARNING 

1000 

OPERATIONAL FLAGS 
Instrument Off 

0100 

In Manual Calibration Mode 

0200 

In Zero Calibration Mode 

0400 

In Span Calibration Mode 

0800 

UNITS OF MEASURE FLAGS 
UGM 

0000 

MGM 

2000 

PPB 

4000 

PPM 

6000 

SPARE/UNUSED BITS 

0080, 8000 

UNASSIGNED FLAGS 
Box Temp Warning 

Analog Cal Warning 

Sample Press Warning 

Cannot Dyn Zero 

System Reset 

Cannot Dyn Span 

Rear Board Not Detected 

Invalid Conc 

Relay Board Warning 

 

Summary of Contents for T101
























































































































































































































































































































































































Reviews:

No comments