manualshive.com logo in svg

Teledyne T101, Operation Manual, Page: 25 / 375

Share
Download
Teledyne T101 Operation Manual Download Page 25

Teledyne ML – T101 Operation Manual 

Introduction 

 

21 

Option 

Option 

Number 

Description/Notes 

Current Loop Analog 

Outputs 

Adds isolated, voltage-to-current  conversion circuitry to the 

analyzer’s analog outputs. 

 

41 

Isolated 0-20 or 4-20 mA  current output (up to three can be retrofitted if not 

installed at the factory) 

Parts Kits 

 

 

 

 

42A 

 

 

43 

Expendables Kit with IZS includes the items needed to refurbish  the 

internal zero air scrubber (IZS) that is included.   

45 

Spare Parts Kit  includes spares parts for one unit. 

NO Optical  Filter 

Recommended  for High NOX backgrounds. 

 

47B 

Required for EN Certification. 

Calibration Valves 

Used to control the flow of calibration gases generated from external 

sources, rather than manually switching the rear panel pneumatic 

connections. 

50A 

Ambient Zero and Ambient Span 

50G 

Zero Scrubber and Internal Span Source (IZS) 

H

2

 S Permeation  Tubes   Replacement  tubes for the IZS option; identical size/shape; different 

effusion rates. 

 

 

Effusion Rate  
(@ 50°C) 

Approximate  

Concentration 

Specified Flow Rate (of indicated perm 

tube rate) 

(uncertified)  52A 

106 ng/min 

.08 -.12 ppm 

0.76 lpm (nominal) ± 25%  

(certified)  52E 

76 ng/min 

.04 - .06 ppm  0.76 lpm ± 5% 

Communication Cables 

For remote  serial, network and Internet communication  with the 

analyzer. 

 

 

Type 

Description 

 

 

60A 

RS-232 

Shielded, straight-through DB-9F to DB-25M cable, about 1.8 m 

long. Used to interface with older computers or code activated 

switches with DB-25 serial connectors. 

 

60B 

RS-232 

Shielded, straight-through DB-9F to DB-9F cable of about 1.8 m 

length.  

 

60C 

Ethernet  Patch cable, 2 meters long, used for Internet  and LAN 

communications. 

 

60D 

USB 

Cable for direct connection between instrument (rear panel USB 

port) and personal computer. 

Concentration Alarm 

Relay 

Issues warning when gas concentration  exceeds limits set by user. 

 

61 

Four (4)  “dry contact” relays on the rear panel of the instrument.  This relay 

option is different from and in addition to the “Contact Closures” that come 

standard on all TML instruments.   

RS-232 Multidrop 

Enables communications  between host computer and up to eight 

analyzers. 

 

62 

Multidrop card seated on the analyzer’s CPU card. 
Each instrument in the multidrop network requires this card and a 

communications cable (Option 60B). 

Special Features 

Built in features, software activated 

 

N/A 

Maintenance Mode Switch,  located inside the instrument, places the 

Summary of Contents for T101
























































































































































































































































































































































































Reviews:

No comments