Teledyne T101 Operation Manual Download Page 214

Page: 214 / 375

Instrument Maintenance

Teledyne ML - T101 Operation Manual

210

Figure 8-4. Critical Flow Orifice Assembly

Take out the components of the assembly: a spring, a sintered filter, two

O-rings and the critical flow orifice.

You may need to use a scribe or pressure from the vacuum port to get the parts out

of the manifold.

Discard the two O-rings and the sintered filter.

Replace the critical flow orifice.

Re-assemble the parts as shown in Figure 8-4 using a new filter and O-

rings.

Reinstall the NPT fitting and connect all tubing.

10.

Power up the analyzer and allow it to warm up for 60 minutes.

11.

Perform a leak check (refer to Section 9.5).

Summary of Contents for T101
























































































































































































































































































































































































Search results

Summary of Contents for T101

Reviews:

Teledyne T101, Operation Manual, Page: 214 / 375

Search results

Summary of Contents for T101

Reviews: