Teledyne T101 Operation Manual Download Page 314

Page: 314 / 375

Teledyne API T/E-Series Models 101, 102, and 108 Software Documentation (PN05492D DCN6485)

A-20

Setup Variable

Numeric

Units

Default

Value

Value Range

Description

ALARM_TRIGGER

Cycles

1–100

Number of times

concentration must exceed

limit to trigger alarm.

FACTORY_OPT

BitFlag

0–65535

Factory option flags. Add

values to combine flags.
1 = enable dilution factor
2 = zero/span valves

installed
4 = IZS installed (implies

zero/span valves installed)
16 = display units in

concentration field
32 = enable software-

controlled maintenance

mode
128 = enable switch-

controlled maintenance

mode
2048 = enable Internet

option

All instances of “H2S” in T101, M101E are changed to “TRS” in T102, M102E, and “TS” in T108, M108E.

T101,

M101E.

T102,

M102E.

T108,

M108E.

Must power-cycle instrument for these options to fully take effect.

Triple-gas

option.

Fast measurement option.

Concentration alarm option.

T108U,

M108EU.

07266B DCN6485

Summary of Contents for T101
























































































































































































































































































































































































Search results

Summary of Contents for T101

Reviews:

Teledyne T101, Operation Manual, Page: 314 / 375

Search results

Summary of Contents for T101

Reviews: