manualshive.com logo in svg

Teledyne T101, Operation Manual, Page: 187 / 375

Share
Download
Teledyne T101 Operation Manual Download Page 187

Teledyne ML – T101 Operation Manual 

Calibration Procedures 

 

183 

It is recommended that, if dynamic calibration is enabled, the analyzer’s test functions, 
slope and offset values be checked frequently to assure high quality and accurate data 
from the instrument. 

6.9.1.

 

AUTOCAL OF INSTRUMENTS IN INDEPENDENT OR AUTO 

REPORTING RANGE MODES 

If the analyzer is being operated in 

IND

 or 

AUTO

 Range mode, then the High and Low 

ranges must be specified as part of the Auto Cal set up.  This  parameter appears at the end 
of the programming sequences after the

 CALIBRATE: ON/OFF

 parameter is set.  For 

example: 

  

 

 

 SETUP X.X

       RANGE TO CAL: LOW

 

 
   <SET 

         

  

 

EDIT

 

 

 

 

         EXIT

 

EXIT 

returns 

to the 

SETUP

 

Menu

 

 

 

 SETUP X.X

       CALIBRATE: ON

 

 
   <SET 

 SET>

   EDIT 

 

 

 

      

   EXIT

 

 

 SETUP X.X

    SEQ 2) ZERO–SPAN,  2:00:30

 

 
PREV  NEXT  

MODE

   

SET 

 

 

      

   EXIT

 

Sequence 

  Delta Time 

 

       MODE          Delta  Days 

 

Follow standard AutoCal programming process to this 

point, then … 

 

 SETUP X.X

       RANGE TO CAL: LOW

 

 

   LOW  

   HIGH

 

 

 

 

         ENT

R    EXIT

 

 

 SETUP X.X

       RANGE TO CAL: HIGH

 

 

   LOW     HIGH 

 

 

 

         

ENTR

    EXIT

 

 

 SETUP X.X

       RANGE TO CAL: HIGH

 

 
   <SET 

         

  

 

EDIT

 

 

 

 

        

 EXIT

 

 

Summary of Contents for T101
























































































































































































































































































































































































Reviews:

No comments