Teledyne T101 Operation Manual Download Page 184

Page: 184 / 375

Calibration Procedures

Teledyne ML – T101 Operation Manual

180

Table 6-3. AutoCal Attribute Setup Parameters

Attribute Name

ACTION

Timer Enabled

Turns on the Sequence timer

Starting Date

Sequence will operate on Starting Date

Starting Time

Sequence will operate at Starting Time

Delta Days

Number of days to skip between each sequence

Delta Time

Incremental delay on each Delta Day that the sequence starts.

Duration

Duration of the sequence in minutes

Calibrate

Enable to do dynamic zero/span calibration, disable to do a cal check only.

This must be set to OFF for units used in US EPA applications and with IZS

option installed.

NOTE

The programmed STARTING_TIME must be a minimum of 5 minutes later than the real

time clock (See Section 4.4.6 for setting real time clock).

NOTE

Avoid setting two or more sequences at the same time of the day. Any new sequence

which is initiated whether from a timer, the COM ports, or the contact closure inputs will

override any sequence which is in progress.

NOTE

If at any time an illegal entry is selected (Example: Delta Days > 367) the ENTR button

will disappear from the display.

Summary of Contents for T101
























































































































































































































































































































































































Search results

Summary of Contents for T101

Reviews:

Teledyne T101, Operation Manual, Page: 184 / 375

Search results

Summary of Contents for T101

Reviews: