manualshive.com logo in svg

Teledyne T101, Operation Manual, Page: 110 / 375

Share
Download
Teledyne T101 Operation Manual Download Page 110

Operating Instructions 

Teledyne  ML  – T101 Operation Manual 

106 

  

The signals from these two connectors are routed from the motherboard via a wiring 
harness to two 10-pin connectors on the CPU card, J11 and J12. 

 

Figure 4-8. CPU Connector Pin-Outs  for RS-232 Mode 

Teledyne ML offers two mating cables, one of which should  be applicable for your use. 

•

 

Part number  WR000077,  a DB-9  female  to DB-9  female  cable, 6  feet long. 

Allows  connection of COM1  with the serial  port of most  personal 

computers. 

•

 

Part number  WR000024,  a DB-9  female  to DB-25  male  cable. Allows 

connection to the most  common  styles of modems  (e.g. Hayes-

compatible)  and code activated switches. 

Both cables are configured with straight-through wiring and should require no additional 
adapters. 

To assist in properly connecting the serial ports to either a computer or a modem, there 
are activity indicators just above the COM1 port.  Once a cable is connected between the 
analyzer and a computer or modem, both the red and green LEDs should be on. If the 
lights for COM 1 are not lit, use small switch on the rear panel to switch it between DTE 
and DCE modes (see Section  4.7.5). If both LEDs are still not illuminated, check the 
cable for proper wiring.  

The two LEDs located over COM2 are currently deactivated.  If you have problems 
getting COM2 to activate, it may be necessary to install a null-modem cable (contact 
Technical Support for information). 

Summary of Contents for T101
























































































































































































































































































































































































Reviews:

No comments