manualshive.com logo in svg

Teledyne T101, Operation Manual, Page: 118 / 375

Share
Download
Teledyne T101 Operation Manual Download Page 118

Operating Instructions 

Teledyne  ML  – T101 Operation Manual 

114 

  

4.7.7.

 

USB CONFIGURATION 

The analyzer can be operated through a personal computer by downloading the TAPI 
USB driver and directly connecting their respective USB ports. 

1.  Install the Teledyne T-Series USB driver on your computer, downloadable from the 

Teledyne API website under Help Center>Software Downloads (www.teledyne-
api.com/software). 

2.  Run the installer file: “TAPIVCPInstaller.exe” 

 

3.  Connect the USB cable between the USB ports on your personal computer and your 

analyzer.  The USB cable should be a Type A –  Type B cable, commonly used as a 
USB printer  cable. 

4.  Determine the Windows XP Com Port number that was automatically assigned to the 

USB  connection.    (Start  →  Control  Panel  →  System  →  Hardware  →  Device 
Manager).  This is the com port that should be set in the communications software, 
such as APICOM  or Hyperterminal. 

 

Refer to the Quick Start (

Direct Cable Connection

) section of the Teledyne APIcom 

Manual, PN 07463. 

Summary of Contents for T101
























































































































































































































































































































































































Reviews:

No comments