manualshive.com logo in svg

Teledyne T101, Operation Manual, Page: 188 / 375

Share
Download
Teledyne T101 Operation Manual Download Page 188

Calibration Procedures  

Teledyne  ML  – T101 Operation Manual 

184 

  

6.9.2.

 

AUTOCAL OF INSTRUMENTS IN MULTIGAS 

MEASUREMENT MODE 

If the analyzer is being operated in multigas measurement mode, auto cal  can only be 
programmed to calibrate the instrument with one of the available gases. 

NOTE 

Make sure that the gas for which the AutoCal sequence has been programmed is being 

supplied to the analyzer at the time the autocal program initiates. 

If the wrong  gas is being supplied to the instrument, the analyzer will be mis-calibrated.  

If the instrument is in multigas measurement mode and the 

SNGL

 reporting range mode 

is selected, the AutoCal sequence is programmed as described above.  If the reporting 
range of the T101  must is set for either 

IND 

or 

AUTO.

  the gas type and range to be 

measured must be specified.  This parameter appears at the end of the programming 
sequences after the

 CALIBRATE: ON/OFF

 parameter is set.  For example: 

 

 

 SETUP X.X

       GAS-RANGE: H2S-HIGH

 

 
   <SET 

         

  

 

EDIT

 

 

 

 

         EXIT

 

 

 SETUP X.X

       CALIBRATE: ON

 

 
   <SET 

 SET>

   EDIT 

 

 

 

      

   EXIT

 

Follow standard AutoCal programming process to this 

point, then … 

 

 SETUP X.X

       GAS TO CAL: H2S

 

 

 

  SO2

  

   

H2S

 

 

 

 

         ENT

R    EXIT

 

 

 SETUP X.X

      Gas TO CAL: SO2

 

 

   LOW     HIGH 

 

 

 

         

ENTR

    EXIT

 

EXIT 

returns 

to the 

SETUP

 

Menu

 

 

 

 SETUP X.X

    SEQ 2) ZERO–SPAN,  2:00:30

 

 
PREV  NEXT  

MODE

   

SET 

 

 

      

   EXIT

 

Sequence 

  Delta Time 

 

       MODE          Delta  Days 

 

 

 SETUP X.X

       RANGE TO CAL: LOW

 

 

   LOW  

   HIGH

 

 

 

 

         ENT

R    EXIT

 

 

 SETUP X.X

       RANGE TO CAL: HIGH

 

 

   LOW     HIGH 

 

 

 

         

ENTR

    EXIT

 

 

 SETUP X.X

         GAS-RANGE: SO2-LOW

 

 
   <SET 

         

  

 

EDIT

 

 

 

 

        

 EXIT

 

 

Summary of Contents for T101
























































































































































































































































































































































































Reviews:

No comments