manualshive.com logo in svg

Teledyne T101, Operation Manual, Page: 241 / 375

Share
Download
Teledyne T101 Operation Manual Download Page 241

Teledyne ML - T101 Operation Manual 

Troubleshooting  & Service

 

 

237 

 

Figure 9-4. Shutter Assembly 

 

CAUTION 

ALWAYS wear UV-Protective, Safety Glasses when working  with  the UV 

Lamp Assembly. 

26.

 

 

1.

 

Set the analyzer  display  to show the signal  I/O  function, 

UVLAMP_SIGNAL. 

2.

 

Slightly loosen the large brass thumbscrew located on the shutter 

housing (refer to Figure 9-5) so that the lamp  can be moved.    

3.

 

While  watching the UVLAMP_SIGNAL  reading,  slowly rotate the lamp  or 

move it back and forth vertically until the UVLAMP_SIGNAL  reading is 

at its maximum.   

NOTE 

DO NOT grasp the UV lamp by its cap when changing its position. 

Always grasp the main body of the lamp. 

4.

 

Compare the UVLAMP_SIGNAL  reading  to the information  in Table 9-2 

and follow the instructions there. 

Summary of Contents for T101
























































































































































































































































































































































































Reviews:

No comments