Teledyne T101 Operation Manual Download Page 242

Page: 242 / 375

Troubleshooting & Service

Teledyne ML - T101 Operation Manual

238

Table 9-9. Example of UV Lamp Power Supply Outputs

UVLAMP_SIGNAL

ACTION TO BE TAKEN

3500mV±200mV.

No Action Required

> 4900mV at any time.

Adjust the UV reference detector potentiometer (refer to Figure 9-6)

until UVLAMP_SIGNAL reads approximately 3600mV before

continuing to adjust the lamp position.

>3700mV or < 3300mV Adjust the UV reference detector potentiometer (refer to Figure 9-6)

until UVLAMP_SIGNAL reads as close to 3500mV as possible.

.< 600mV

Replace the lamp.

Figure 9-5. Location of UV Reference Detector Potentiometer

Finger-tighten the thumbscrew.

NOTE

DO NOT over-tighten the thumbscrew.

9.6.3.

REPLACING THE UV LAMP

Turn off the analyzer.

27.

Disconnect the UV lamp from its power supply.

•

You can find the power supply connector by following the two, white

UV Lamp power supply wires from the lamp to the power supply.

28.

Loosen, but do not remove the two UV lamp bracket screws and the

large brass thumbscrew located on the shutter housing (refer to Figure

9-4) so that the lamp can be moved.

Summary of Contents for T101
























































































































































































































































































































































































Search results

Summary of Contents for T101

Reviews:

Teledyne T101, Operation Manual, Page: 242 / 375

Search results

Summary of Contents for T101

Reviews: