manualshive.com logo in svg

Teledyne T101, Operation Manual, Page: 133 / 375

Share
Download
Teledyne T101 Operation Manual Download Page 133

Teledyne ML – T101 Operation Manual 

Operating Instructions 

 

129 

 

LIST OF PARAMETERS 

NAME: 

PNUMTC

 

EVENT: 

ATIMER

 

REPORT PERIOD: 

001:00:00

 

NO. OF RECORDS:

 360 

RS-232 REPORT: 

OFF

 

CHANNEL ENABLED: 

ON

 

CAL HOLD OFF:

 OFF

 

 

NAME: 

CALDAT

 

EVENT: 

SLPCHG

 

NO. OF RECORDS:

200 

RS-232 REPORT: 

OFF

 

CHANNEL ENABLED: 

ON

 

CAL HOLD OFF:

 OFF

 

 

PARAMETER: 

SMPLFLW 

MODE:

 AVG 

PRECISION: 

1 

STORE NUM SAMPLES 

OFF

 

PARAMETER: 

SMPLPRS 

MODE:

 AVG 

PRECISION: 

1 

STORE NUM SAMPLES 

OFF

 

PARAMETER: 

S2OFS1 

MODE:

 INST 

PRECISION: 

1 

STORE NUM SAMPLES 

OFF

 

PARAMETER: 

S2SLP1 

MODE:

 INST 

PRECISION:

3 

STORE NUM SAMPLES 

OFF

 

PARAMETER: 

S2ZSC1 

MODE: 

INST 

PRECISION: 

1 

STORE NUM SAMPLES 

OFF

 

PARAMETER: 

S2CONC1 

MODE:

 AVG 

PRECISION: 

1 

STORE NUM SAMPLES 

OFF

 

PARAMETER: 

S2CONC1 

MODE:

 AVG 

PRECISION: 

1 

STORE NUM SAMPLES 

OFF

 

NAME: 

CONC

 

EVENT: 

ATIMER

 

REPORT PERIOD: 

000:00:05

 

NO. OF RECORDS:

 4032 

RS-232 REPORT: 

OFF

 

CHANNEL ENABLED: 

ON

 

CAL HOLD OFF:

 ON

 

LIST OF CHANNELS 

 

Figure 4-11.  Default DAS Channels Setup 

These default Data Channels can be used as they are, or they can be customized from the 
front panel to fit a specific application. They can also be deleted to make room for custom 
user-programmed Data Channels.  

Appendix A-5 lists the firmware-specific  DAS  configuration in plain-text format. This 
text file can either be loaded into APICOM and then modified and uploaded to the 
instrument or can be copied and pasted into a terminal program to be sent to the analyzer. 

NOTE 

Sending an DAS  configuration  to the analyzer through  its COM ports will  replace the 

existing configuration  and will delete all stored data. Back up any existing data and the 

DAS configuration  before uploading new settings. 

Summary of Contents for T101
























































































































































































































































































































































































Reviews:

No comments