manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 10 / 346

Share
Download
Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 10

Table of contents 

 

  

 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 

8

 

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

7.5.2 

Ramp-function generator .......................................................................................................... 203 

7.6 

Motor control ............................................................................................................................. 204 

7.6.1 

V/f control .................................................................................................................................. 206 

7.6.1.1  V/f control with linear and square-law characteristic................................................................. 206 

7.6.1.2  Additional characteristics for the V/f control.............................................................................. 207 

7.6.1.3  Optimizing with a high break loose torque and brief overload.................................................. 208 

7.6.2 

Vector control ............................................................................................................................ 210 

7.6.2.1  Properties of vector control ....................................................................................................... 210 

7.6.2.2  Commissioning vector control................................................................................................... 210 

7.6.2.3  Torque control ........................................................................................................................... 211 
7.7 

Protection functions................................................................................................................... 212 

7.7.1 

Inverter temperature monitoring................................................................................................ 212 

7.7.2 

Motor temperature monitoring using a temperature sensor...................................................... 213 

7.7.3 

Protecting the motor by calculating the motor temperature...................................................... 215 

7.7.4 

Overcurrent protection .............................................................................................................. 215 

7.7.5 

Limiting the maximum DC link voltage...................................................................................... 216 

7.8 

Status messages....................................................................................................................... 218 

7.8.1 

System runtime ......................................................................................................................... 218 

7.9 

Application-specific functions.................................................................................................... 219 

7.9.1 

Unit changeover ........................................................................................................................ 219 

7.9.1.1  Changing over the motor standard ........................................................................................... 220 

7.9.1.2  Changing over the unit system ................................................................................................. 221 

7.9.1.3  Changing over process variables for the technology controller................................................ 222 

7.9.1.4  Changing of the units with STARTER....................................................................................... 223 

7.9.2 

Braking functions of the converter ............................................................................................ 225 

7.9.2.1  Comparison of electrical braking methods................................................................................ 225 

7.9.2.2  DC braking ................................................................................................................................ 228 

7.9.2.3  Compound braking.................................................................................................................... 232 

7.9.2.4  Dynamic braking ....................................................................................................................... 234 

7.9.2.5  Braking with regenerative feedback to the line ......................................................................... 236 

7.9.3 

Automatic restart and flying restart ........................................................................................... 237 

7.9.3.1  Flying restart – switching on while the motor is running ........................................................... 237 

7.9.3.2  Automatic switch-on .................................................................................................................. 239 

7.9.4 

PID technology controller.......................................................................................................... 243 

7.9.5 

Load torque monitoring (system protection) ............................................................................. 244 

7.9.6 

Load failure monitoring via digital input..................................................................................... 246 

7.9.7 

Real time clock (RTC) ............................................................................................................... 247 

7.9.8 

Time switch (DTC) .................................................................................................................... 249 

7.9.9 

Temperature sensing using temperature-dependent resistors................................................. 250 

7.9.10  Essential service mode ............................................................................................................. 252 

7.9.11  Multi-zone control...................................................................................................................... 257 

7.9.12  Cascade control ........................................................................................................................ 261 

7.9.13  Bypass....................................................................................................................................... 265 

7.9.14  Energy-saving mode ................................................................................................................. 269 

7.9.15  Logical and arithmetic functions using function blocks ............................................................. 275 
7.10 

Switchover between different settings ...................................................................................... 279 

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Reviews:

No comments