manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 268 / 346

Share
Download
Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 268

Functions 

 

7.9 Application-specific functions 

 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 

266

 

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

When changing over to inverter operation, initially contactor K2 must be opened and after 

the de-excitation time, contactor K1 is closed. The inverter then captures the rotating motor 

and the motor is operated on the inverter. 

Bypass function when activating via a control signal (p1267.0 = 1) 

The status of the bypass contactors is evaluated when the inverter is switched on. If the 

automatic restart function is active (p1210 = 4) and an ON command (r0054.0 = 1) as well as 

the bypass signal (p1266 = 1) are still present at power up, then after power up, the inverter 

goes into the "ready and bypass" state (r899.0 = 1 and r0046.25 = 1) and the motor 

continues to run directly connected to the line supply. 

S

%\SDVVFRPPDQG

U 6LJQDOIRUFRQWDFWRU.

,QYHUWHURSHUDWLRQ

S>@)HHGEDFNIURP.

,QYHUWHURSHUDWLRQ

S>@ 0RQLWRULQJWLPH.

,QYHUWHURSHUDWLRQ

U 6LJQDOIRUFRQWDFWRU.

/LQHRSHUDWLRQ

S>@ )HHGEDFNIURP.

/LQHRSHUDWLRQ

S>@ 0RQLWRULQJWLPH.

/LQHRSHUDWLRQ

5DWHGPRWRUVSHHG

$FWXDOVSHHGIURPWKHLQYHUWHU

,QYHUWHU

RSHUDWLRQ

,QYHUWHU

RSHUDWLRQ

6ZLWFKRYHU

SKDVH

6ZLWFKRYHU

SKDVH

/LQH

RSHUDWLRQ

3RZHUXS

)O\LQJ

UHVWDUW

S

S

S

S

S

S

S

S

S

S

S

W

W

W

W

W

W

W

W

 

Figure 7-21  Bypass control independent of the speed via a control signal (p1267.0 = 1) 

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Reviews:

No comments