Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 69

Page: 69 / 346

Commissioning

4.4 Commissioning with the BOP-2

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

Identifying motor data

If you select the MOT ID (p1900) during basic commissioning, alarm A07991 will be issued

once basic commissioning has been completed. To enable the converter to identify the data

for the connected motor, you must switch on the motor (e.g. via the BOP-2). The converter

switches off the motor after the motor data identification has been completed.

CAUTION

Motor data identification for dangerous loads
Secure dangerous plant and system parts before starting the motor data identification, e.g.

by fencing off the dangerous location or lowering a suspended load to the floor.

4.4.4

Additional settings

The Section Commissioning (Page 53) shows you what still has to be set after the basic

commissioning in order to adapt the inverter to your application.

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews:

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 69 / 346

Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews: